Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Archived SH Discussions [Q&A Thread from Jun-2014 thru Aug 2015]
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(12-30-2014, 09:32 AM)Jamesxfce Wrote: His is USB setup but i did transfer the information to my hard drive, when I get home and get a hold of a SD Card, I will try to import it that way, on a related note I was able to get it running via Windows Virtual Box, but the dates are completely sporadic, while he may not be using it every day, I doubt this machine is so good that it can tell when he is going to use it up until Oct 2016...

you checked the date/time setting on his cpap? that is weird....
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(12-30-2014, 01:03 PM)DariaVader Wrote:
(12-30-2014, 09:32 AM)Jamesxfce Wrote: His is USB setup but i did transfer the information to my hard drive, when I get home and get a hold of a SD Card, I will try to import it that way, on a related note I was able to get it running via Windows Virtual Box, but the dates are completely sporadic, while he may not be using it every day, I doubt this machine is so good that it can tell when he is going to use it up until Oct 2016...

you checked the date/time setting on his cpap? that is weird....

I'll call him and check out the date issue, I think it was a refurb/or reuse because some of the dates go way to far back, before he was even using it different pressure settings too.
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(12-30-2014, 02:06 PM)Jamesxfce Wrote: I'll call him and check out the date issue, I think it was a refurb/or reuse because some of the dates go way to far back, before he was even using it different pressure settings too.

Might be worth doing a data wipe then and starting from fresh. The refurby guys shoulda done that!
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
Yeah, they are more worried about getting out of the door more than if you are getting the right treatment, they never take my dads data in to check and see if his therapy is working. And it seems to not be as according to my mother, logs are still being cut (Read: Snoring)
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(12-30-2014, 02:06 PM)Jamesxfce Wrote: ... some of the dates go way too far back ...

ahah! this was one of the few primitive 1916 models. no wonder you are having trouble getting SH to read it. just add the {sharpened stick impression in clay} interface module, and recompile it. Laugh-a-lot
Dedicated to QALity sleep.
Trouble installing Sleepyhead
Every time I try to run the Sleepyhead software on my laptop, I get a message saying that it can't install because it's missing the "Qt5core.dll", although the file shows up in the folder after extracting from the zip file. I have to go back in and d/l and install it all over again. Anyone else have this problem and is there a workaround?

Thanks

PS: I apologize for not posting this in the appropriate thread. After seeing the main board, I attempted to delete this post and repost in the Sleepyhead thread but I couldn't delete it.
RE: Trouble installing Sleepyhead
(01-04-2015, 08:38 AM)novatom Wrote: Every time I try to run the Sleepyhead software on my laptop, I get a message saying that it can't install because it's missing the "Qt5core.dll", although the file shows up in the folder after extracting from the zip file. I have to go back in and d/l and install it all over again. Anyone else have this problem and is there a workaround?

Thanks

PS: I apologize for not posting this in the appropriate thread. After seeing the main board, I attempted to delete this post and repost in the Sleepyhead thread but I couldn't delete it.

I was getting that in the Virtual machine that i was running, you need to make sure it is the correct file (system32 for x86 and SysWow64 i think for the X86_64 bit systems) and just for good measure, make sure a copy is in with the programs data file, so that if it initiates a fall back for some reason, it can pull from its local directory. also run it under windows xp compatibility tends to help also.
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(12-28-2014, 07:52 PM)SuperSleeper Wrote: Hi Tim,

JediMark runs the private, invitation-only SleepyHead Testing Forum here on Apnea Board for his group that helps with development and testing. I have re-posted your report in the bug report thread on that forum so that perhaps one of the developers or testers may see it and respond back here in this thread.

Thanks.

Coffee
Supersleeper: I would be happy to participate in testing, if invited.

I have been using Sleepyhead for 6 months, but I am still not happy with Daily Graphs in terms of selected vertical scale parameter labeling, nor with scale divisions and ranges. Also, my By Pressure graph runs from 4.5 to 7.5 cm, although I have a constant pressure of 6 cm (water), so this graph is not really applicable to my CPAP.

For Leak Rate I have 2 parallel graphs 22 units apart. The vertical axis has every fourth index marked by increments of 11, so each increment is 11/4 of a Litre/Min! I would like to see the vertical axes given sensible labels, with dimensional units specified (perhaps on a second line)! The increments should be integer numbers (or decimal fractions of integers, ie to conform with scientific practice. The Snore label is apparently Snore Volume in unspecified units, again with an awkward scale.

The Tidal Volume has a maximum range of 5950 mL (sic) although a typical value is 292.3 mL. So the graph line only occupies a small part of this range. There is a spike that is almost 4740.0 mL, although the green cursor reads the value as 484.96

There are some unlabelled user controls for the display (at the bottom of the page), which I am not quite sure how they work, but look like they could be useful to customize the display.

These remarks, although criticisms, are meant to be helpful in increasing the utility of what are very complex and revealing displays. My expectation is that they will be ignored. However I remain available for dialog, and would be happy to submit suggested improvements as relate to my specific graphs, as examples that may need adjustment to fit the complete range of graphs applicable to current users.
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(01-05-2015, 12:48 PM)Coroboree Wrote: Supersleeper: I would be happy to participate in testing, if invited.

I have been using Sleepyhead for 6 months, but I am still not happy with Daily Graphs in terms of selected vertical scale parameter labeling, nor with scale divisions and ranges. Also, my By Pressure graph runs from 4.5 to 7.5 cm, although I have a constant pressure of 6 cm (water), so this graph is not really applicable to my CPAP.

For Leak Rate I have 2 parallel graphs 22 units apart. The vertical axis has every fourth index marked by increments of 11, so each increment is 11/4 of a Litre/Min! I would like to see the vertical axes given sensible labels, with dimensional units specified (perhaps on a second line)! The increments should be integer numbers (or decimal fractions of integers, ie to conform with scientific practice. The Snore label is apparently Snore Volume in unspecified units, again with an awkward scale.

The Tidal Volume has a maximum range of 5950 mL (sic) although a typical value is 292.3 mL. So the graph line only occupies a small part of this range. There is a spike that is almost 4740.0 mL, although the green cursor reads the value as 484.96

There are some unlabelled user controls for the display (at the bottom of the page), which I am not quite sure how they work, but look like they could be useful to customize the display.

These remarks, although criticisms, are meant to be helpful in increasing the utility of what are very complex and revealing displays. My expectation is that they will be ignored. However I remain available for dialog, and would be happy to submit suggested improvements as relate to my specific graphs, as examples that may need adjustment to fit the complete range of graphs applicable to current users.

What version are you running? I don't see what you're describing in v9.9.8.1-testing.
Crimson Nape
Apnea Board Moderator
www.ApneaBoard.com
___________________________________
Useful Links -or- When All Else Fails:
The Guide to Understanding OSCAR
OSCAR Chart Organization
Attaching Images and Files on Apnea Board
Apnea Helpful Tips

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
RE: SleepyHead Software - Beginner's Guide, Questions, Answers & Discussion
(01-05-2015, 12:48 PM)Coroboree Wrote: Supersleeper: I would be happy to participate in testing, if invited.

See JediMark's info on this here (scroll down to the "Latest News" section where it reads "Secret Beta Stuff":

http://www.sleepfiles.com/SH/

If you meet the criteria, send JediMark a PM (Private Message). I'm not sure he's available these days since he's got other things going on, so it may be a long time before he's able to answer you.

SuperSleeper
Apnea Board Administrator
www.ApneaBoard.com


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.




Possibly Related Threads...
Thread Author Replies Views Last Post
  Another OSCAR cannot find data thread - with a twist. Cuppa 63 3,989 03-02-2023, 04:30 AM
Last Post: Cuppa
  OSCAR v1.3.0 is released [old archived thread] Gideon 36 7,516 02-07-2023, 06:58 PM
Last Post: SuperSleeper
  Looking for DreamStation 2 samples using 12mm heated tube [thread closed] sawinglogz 6 1,205 01-14-2022, 04:43 PM
Last Post: SuperSleeper
Arrow ResScan CPAP Reporting Software (OLD version: 5.5) [Archived Discussions] SuperSleeper 1,109 1,649,076 08-25-2015, 07:10 PM
Last Post: SuperSleeper
  New ResScan Version 5.4.1 - updated June 19, 2015 [old version] SuperSleeper 3 9,317 07-21-2015, 03:58 PM
Last Post: spursfan1965
Idea Updates to SleepyHead [May 2015] SuperSleeper 21 7,362 06-26-2015, 04:45 PM
Last Post: Mark Douglas
Arrow EncoreBasic 2.4.8.0 CPAP Reporting Software [Archived read-only thread] EncoreBasic User 142 88,578 02-18-2015, 11:29 AM
Last Post: on the virge


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.