Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account

New Posts   Today's Posts

[CPAP] Understanding Flow Rate
[Image: 20170224Screen.jpg]

Had  a good night on my cpap machine, the last hour and a half was really good, my question is the flow rate is high and steady, is that because the leak rate is right down?
Is a high flow rate a good or bad thing?
Post Reply Post Reply
Looks like you are breathing rather shallow for much of the night.
Looking at your median statistics, your tidal volume of 340 ml is low; most are closer to 500 ml.
Your median Minute Ventilation is also low.

MV = TV x Resp Rate. for the median: 4.38 LPM = .34 Liters x 12.8 per minute.

As for what happened at 04:00 -- perhaps a shift in sleep position?

I've not been following your prior posts. I am wondering if you need a bilevel machine to increase TV.
Post Reply Post Reply
I mainly sleep on my back because I have sore shoulders. At about 4 I did change on to my right shoulder so that would explain that.
I have my flex setting on 2. Would changing that have any effect on the flow rate?
Had 2 loan machines one on auto then switched to cpap at 13 pressure. Ahi is much better on the fixed pressure.
Would a change of pressure change the flow rate? like go to 14 or change the flex?

Post Reply Post Reply

I looked at some of your prior posts. Looks like you are walking a tightrope between OA and CA. Increasing pressure might increase CAs.
Sleeprider responded; and he's very knowledgeable.

Here's the way I think things would go:
In today's medical system, they would say your present results are "good enough".

In a system oriented to best outcome, you would have a trial in a bilevel; likely fail due to CA being too high.
Then, be issued an ASV machine.

My best advice is to side sleep to the degree you can. Try to discuss your results with your doctor. Your doc may say "good enough" or may delve deeper.
Post Reply Post Reply
Thanks for your replies. I tried 2 things last night, and that was to set the flex to 3 and try sleeping on my side a lot more. Also turned my humidity down as my nose feels stuffed when I take the mask off. For the first few breaths with the mask off I can hardly breath through my nose. Here is the chart. What is with the breathing not detected -157.41%

[Image: 20170225screen.jpg]
Post Reply Post Reply
You can see the periods of higher flow. Your median TV and MV is up.

The BND of -157.41% is a program bug. Sleepyhead is a product of a fellow hosehead from Oz.
It's a huge effort because it tries to read all machines and multilingual capability.
Post Reply Post Reply

Possibly Related Threads...
Thread Author Replies Views Last Post
  New to CPAP, need help understanding SleepyHead data bricked 8 304 10-13-2017, 12:27 PM
Last Post: bricked
  [Diagnosis] single pressure rate ,why? buddygirl15 8 269 10-11-2017, 03:02 PM
Last Post: buddygirl15
Wink Experiencing High Leak Rate (ResMed S9) sleepy Bruce 1 181 10-08-2017, 08:37 AM
Last Post: Sleeprider
  Very High Leak Rate Grmato10 94 4,835 10-08-2017, 01:46 AM
Last Post: trunkizback
  Understanding Leak Data, HELP for DUMMIES PLEASE! TrailerSweetheart 11 761 10-05-2017, 11:32 AM
Last Post: Barnfresh
  Am I understanding flatulence could be in my future? HalfAsleep 12 374 09-25-2017, 10:49 AM
Last Post: SarcasticDave94
  [Treatment] Flow Limitations, a problem or not? storywizard 9 278 09-23-2017, 08:34 AM
Last Post: Sleeprider

Forum Jump:

New Posts   Today's Posts

About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.