Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

[CPAP] Whining siren noise and bearing replacement/repair
#11
Hi clintga,
WELCOME! to the forum.!
Great job on getting your machine fixed and thanks for the information.
Much success to you with your CPAP therapy.
trish6hundred
Post Reply Post Reply
#12
That's awesome that you got your machine all fixed up. It's good to know about the bearings if mine ever dies.
Post Reply Post Reply
#13
You know, I may try that tactic with my S-9 with the growly bearings.

OMMOHY
Post Reply Post Reply


#14
bearings generally start dragging before noise is audible causing stress elsewhere - increased current draw and erratic back EMF. Is why I asked about hours. I may want to just change the bearings as a wear item.
I use my PAP machine nightly and I feel great!
Updated: Philips Respironics System One (60 Series)
RemStar BiPAP Auto with Bi-FlexModel 760P -
Rise Time x3 Fixed Bi-Level EPAP 9.0 IPAP 11.5 (cmH2O)
Post Reply Post Reply
#15
(04-23-2015, 04:00 PM)clintga Wrote: They are shielded bearings. I will try to attach a pic. Google plus made the pic not very clear. The right bearing had a small amount of rust. The left bearing could have been used longer. But as a precaution, I changed out both.

Those bearing look very similar to the brush roller bearings I just replaced in my Dyson.


Using FlashAir W-03 SD card in machine. Access through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie

Post Reply Post Reply
#16
(04-24-2015, 02:06 PM)AlanE Wrote:
(04-23-2015, 04:00 PM)clintga Wrote: They are shielded bearings. I will try to attach a pic. Google plus made the pic not very clear. The right bearing had a small amount of rust. The left bearing could have been used longer. But as a precaution, I changed out both.

Those bearing look very similar to the brush roller bearings I just replaced in my Dyson.

bearings are bearings and the descriptor standardized. is no problem to acquire. example expensive wheel bearing in Jag XKE is same as cheap bearing in Chevy. Do not ask how I learned this as a youth.

I use my PAP machine nightly and I feel great!
Updated: Philips Respironics System One (60 Series)
RemStar BiPAP Auto with Bi-FlexModel 760P -
Rise Time x3 Fixed Bi-Level EPAP 9.0 IPAP 11.5 (cmH2O)
Post Reply Post Reply


#17
(04-24-2015, 02:35 PM)Mark Douglas Wrote: bearings are bearings and the descriptor standardized. is no problem to acquire. example expensive wheel bearing in Jag XKE is same as cheap bearing in Chevy. Do not ask how I learned this as a youth.

Pnless they have a PMA number associated with them (aircraft). Then they get more expensive. Just because.

Post Reply Post Reply
#18
(04-24-2015, 02:35 PM)Mark Douglas Wrote: ...example expensive wheel bearing in Jag XKE is same as cheap bearing in Chevy. Do not ask how I learned this as a youth.

So, you used the expensive Jag bearing in your Chevy.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#19
(04-24-2015, 10:59 PM)justMongo Wrote:
(04-24-2015, 02:35 PM)Mark Douglas Wrote: ...example expensive wheel bearing in Jag XKE is same as cheap bearing in Chevy. Do not ask how I learned this as a youth.

So, you used the expensive Jag bearing in your Chevy.

I commend your dry sense of humor! LOL
I use my PAP machine nightly and I feel great!
Updated: Philips Respironics System One (60 Series)
RemStar BiPAP Auto with Bi-FlexModel 760P -
Rise Time x3 Fixed Bi-Level EPAP 9.0 IPAP 11.5 (cmH2O)
Post Reply Post Reply


#20
(04-24-2015, 10:58 AM)Mark Douglas Wrote: bearings generally start dragging before noise is audible causing stress elsewhere - increased current draw and erratic back EMF. Is why I asked about hours. I may want to just change the bearings as a wear item.

Probably in the neighborhood of 18,000 hours...as an estimate. I don't think my machine will tell me the exact hours.
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Modification to Reduce noise in Dreamstation from hose to mask stephennic 16 2,146 04-18-2017, 08:13 PM
Last Post: midgarden
  Cpap repair shops aconcepts 1 136 04-16-2017, 05:22 PM
Last Post: Mosquitobait
  Noise level of Respironics Dreamstation vs Resmed Airsense 10 scottlink96 48 8,124 04-02-2017, 11:30 AM
Last Post: Hydrangea
Sad [Equipment] ResMed Airsense 10 noticeable noise hungrycactus 8 1,087 04-02-2017, 10:42 AM
Last Post: Whitevaliant
  Aircurve V10 Auto making clicking noise silversnore 8 217 03-28-2017, 01:55 AM
Last Post: PoolQ
  ResMed AirCurve 10 ST-A replacement for Respironics System One biPap AVAPS OldPolioLady 2 253 02-07-2017, 09:37 PM
Last Post: trish6hundred
Gross [CPAP] Respironics REMStar System One Series 60 Repair lempface 6 465 02-04-2017, 07:01 AM
Last Post: cate1898

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.