Hello Guest,
Welcome to Apnea Board !As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address. Login or Create an Account
[CPAP] s9 autoset leak
|
08-25-2014, 07:11 PM
s9 autoset leak
I have recently purchased a resmed S9 autoset. An example of my readings are- mask fit good ,AHI 3.4,Leak 32 (which I believe is much too high. I have even taped my mouth up which has no bearing on the reading.Has anyone else had this problem?If so what did they do about it?
08-25-2014, 07:23 PM
RE: s9 autoset leak
Lots of people have that problem Bill. The answer is to re-evaluate your mask fit. I don't much care for the "mask fit" thing the machine does. It usually thinks what it needs to do is insure the mask won't leak at a very high pressure. Then, in the real world, the mask is "fitted" too tight. So it's uncomfortable, and often the little pillows don't inflate right, and everything gets unhappy.
The mask should be snug when you put it on, not tight. If it's tight when you put it on it's going to be too tight under pressure. The other issue is mouth leaks, which it sounds like you suspect. I don't believe in "taping." It just seems to me to be a bad idea waiting to happen. However a chinstrap is frequently needed to "encourage" the jaw to stay forward and the mouth to stay shut. That's primarily to establish the proper position for the airway block, which is the tongue held against the roof of the mouth. It takes a little getting used to but in a few days you'll be a pro.
08-25-2014, 07:28 PM
RE: s9 autoset leak
Hi BILL,
WELCOME! to the forum.! You might try a chinstrap to see if that will help you get your leaks under control. Hang in there for more suggestions and best of luck to you with your CPAP therapy.
trish6hundred
08-25-2014, 07:30 PM
RE: s9 autoset leak
Thanks Retired _ Guy. I omitted to say that I am also using a chin strap.
08-25-2014, 07:34 PM
RE: s9 autoset leak
Ok Bill, use the chinstrap UNDER the mask. Otherwise frolicking about in the night the chinstrap can cause the mask to leak.
08-25-2014, 07:58 PM
RE: s9 autoset leak
(08-25-2014, 07:11 PM)BILL COLLINS Wrote: I have recently purchased a resmed S9 autoset. An example of my readings are- mask fit good ,AHI 3.4,Leak 32 (which I believe is much too high.Not necessary, just mean leak at or below 32 L/m for 95% of the night and not 32 L/m throughout the night As long as mask fit is good, the machine have no problem with leak I use chinstrap and goes over the mask, keep the mask in place I don,t have problems with leaks as long as not disturb my sleep or air escape from the top of the mask into the eyes |
« Next Oldest | Next Newest »
|
Possibly Related Threads... | |||||
Thread | Author | Replies | Views | Last Post | |
AirSense 10 leak rate baseline issue | Phil7 | 8 | 1,514 |
8 hours ago Last Post: FriedRice |
|
Please, need help reading the leak rate and LL info | chronic | 14 | 364 |
04-13-2024, 12:00 PM Last Post: chronic |
|
Leak Spikes and A Break in Flow | blu15 | 9 | 1,279 |
04-06-2024, 02:08 PM Last Post: avhenry |
|
Airsense 10 - AHI account for leak rate? | FriedRice | 10 | 435 |
03-29-2024, 12:29 PM Last Post: Deborah K. |
|
Mouth leak with new machine | LaraM | 4 | 227 |
03-29-2024, 09:58 AM Last Post: PeaceLoveAndPizza |
|
Need help with Airsense 10 AutoSet | JonUK | 2 | 219 |
03-25-2024, 06:11 PM Last Post: JonUK |
|
Fixed mask leak, but flow limit seems to be increasing AHI | emile.leplattenier | 3 | 220 |
03-19-2024, 11:00 AM Last Post: staceyburke |