Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Changing the date on F&P Icon Auto?
#1
Hello Everyone!

I'm a newbe, I have been using my cpap close to a week now.
Took to it rate away, Like a fish in water.

I have a Fisher & Paykel Icon Auto
With heated tube and Humidifier, Nice.

I have one item (setup) that I'm would like to figure out with some help.

My Sleep data is being saved to the USB stick,
However, It's still time stamping with the old date information 12.01.2007

I have looked at the setup menu and can't seem to find where to change the date ?

Can anyone help with this information ?

I'm thinking that it must be there, And I may be brain dead ? Can't see it!

Also, Thanks for your help in regards to downloading:
The Setup Manual.
And The Sleepy Head Software.

Great Board!
Thanks,
Dick
[/size][/font]
Post Reply Post Reply
#2
(07-31-2014, 05:39 PM)dp43 Wrote: Hello Everyone!

I'm a newbe, I have been using my cpap close to a week now.
Took to it rate away, Like a fish in water.

I have a Fisher & Paykel Icon Auto
With heated tube and Humidifier, Nice.

I have one item (setup) that I'm would like to figure out with some help.

My Sleep data is being saved to the USB stick,
However, It's still time stamping with the old date information 12.01.2007

I have looked at the setup menu and can't seem to find where to change the date ?

Can anyone help with this information ?

I'm thinking that it must be there, And I may be brain dead ? Can't see it!

Also, Thanks for your help in regards to downloading:
The Setup Manual.
And The Sleepy Head Software.

Great Board!
Thanks,
Dick
[/size][/font]
Hi dp43,
WELCOME! to the forum.!
I'm glad to hear that you took well to CPAP therapy. I don't know the answer to your question regarding the data information but hang in there and someone will be along to help you, soon.
Best of luck to you and keep up the good work.
trish6hundred
Post Reply Post Reply
#3
Dick, this page shows how to change the time on your machine... it may also be similar procedure for changing the date:

http://www.apneaboard.com/wiki/index.php...F.26P_Icon

Perhaps someone else who has one of the Icons can tell us for sure.

Thinking-about
SuperSleeper
Apnea Board Administrator
www.ApneaBoard.com


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.



Post Reply Post Reply


#4
I'll say it again, Great Board!

The time setting has never been a problem, But I don't seem to have that date menu,
And it doesn't continue after the time is set ?

No problem, I'm working around that, The date is no problem, I just change the dates on the files.

Being a newbe, And a quick learner I have a few wrinkles to work out, And I will.

Speaking of wrinkles, I have a couple more, And the second wrinkle being the most important.
Fisher & Paykel ICON AUTO
Does anyone have any information about the error codes ?
Like: 5.00 , 5.02 , 5.03 , 5.07

I think I figured the 5.00 , Blower / Fan Failure!

And now for my most important thing I need to do rate away!
I'm looking to buy a replacement Blower (Fan) ASAP if anyone has information on where to purchase ?

At 7:30am this morning my F&P Icon Auto QUIT !
Actually the Blower quit and I believe left me with a 5.00 error.

I've only be using this machine for about 4 days, And now I want to keep using it!
I purchased this machine as used but never used, It had been setting around for a few years
I'm sure it picked up some moisture and whatever.

I figured I have nothing to loose, So I'll take it apart and look it over. And I did!
Yup, The blower or Fan was not working, The bearing sounded a little dry.
I managed to get a little lube down the shaft, Noticed a little rust, So I guess moisture got it!

Anyway, It's back up and running for who knows how long.
Tonight and a few more nights would be great.

So if anyone can help, I need to purchase a new or used blower.

Thank you SuperSleeper for the move and the push!

Thanks All,
dick
Post Reply Post Reply
#5
(08-02-2014, 06:47 PM)dp43 Wrote: Does anyone have any information about the error codes ?
Like: 5.00 , 5.02 , 5.03 , 5.07

I think I figured the 5.00 , Blower / Fan Failure!
Hi dp43
From Icon technical manual http://www.apneaboard.com/file_links121/...Manual.pdf
Error codes
Fault NO: 5.0-5.8
DESCRIPTION: Motor Faults
INDICATION: Error symbol
ACTION: Disconnect from power, then connect and re-start device. If error persists, return device

Supplier #2 is good source of new and used machines
http://www.apneaboard.com/forums/Thread-...plier-List

Post Reply Post Reply
#6
Thanks for the information with the Icon technical manual, Great.

I have checked out the source list, Will check again later.

thanks again,
dick
Post Reply Post Reply


#7
Yes, Supplier #2 is a good source!

Just did a little business with them.

Still looking high and low for a blower motor for my F&P icon auto.
Been surfing for days!
No luck yet!

thanks,
dick
Post Reply Post Reply
#8
While still looking around for a Motor for my F&P Icon Auto I have purchased a new Cpap.

My new best friend is the:
DeVilbiss IntelliPAP™ Auto

I might setup it up tonight ? Doing some reading!

And yes, I have questions, What fun would we have without questions, And hopefully answers ?

Is there any way to read the DeVilbiss IntelliPAP data with just a cable,
Or is the SmartLink Module and Data Card a must.
It would be nice if SleepyHead could read this direct.
That might be wishful thinking.
Just saying!

thanks,
dick
Post Reply Post Reply
#9
Good Evening,

If anyone has any new information,
I'm still looking for a replacement Motor for my:
Fisher & Paykel Icon Auto

thanks.
Post Reply Post Reply


#10
you will not typically find parts for medical devices on the open market as only qualified and approved (by the mfgr) repair centers will have them. Some mfgrs will only do in house repairs.

If it is a bad bearing and it is a removeable type, it may be able to be sourced if you can measure it acurritly.

Tom
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Changing PCP is a nightmare in the US TimtheEnchanter 8 252 12-10-2017, 03:52 PM
Last Post: KSMatthew
  changing from CPAP to APAP- which pressure to use? cbrts765 16 584 12-08-2017, 09:05 AM
Last Post: Sleep2Snore
  SD card is not showing date sleepytimegal 4 163 12-05-2017, 07:12 PM
Last Post: sleepytimegal
  Changing the temperature JennyJ 10 274 12-04-2017, 05:09 AM
Last Post: Sleep2Snore
  Changing from APAP to Bilevel alps 13 372 12-02-2017, 01:15 PM
Last Post: alps
  [Equipment] AirSense 10 for Her - changing sleep periods? jaw2004 4 251 10-31-2017, 08:46 PM
Last Post: jaw2004
  [Equipment] Alt Way of Changing Primary Machine in Dreammapper scneal 2 136 10-20-2017, 07:18 AM
Last Post: scneal

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.