Post Reply 
ClimateLineAir Tubing
Author Message
Jacqv21 Offline

Members

Posts: 4
Joined: Jan 2015

Machine: Resmed AirSense10
Mask Type: Full face mask
Mask Make & Model: Unsure
Humidifier: ClimateLineAir
CPAP Pressure: 5-10
CPAP Software: ResScan

Other Comments:

Sex: Female
Location:

Post: #1
ClimateLineAir Tubing
I have been trying the ResMed AirSense 10 with the ClimateLineAir tubing for about a month. I started out with the full face mask but found I kept knocking it to the side in my sleep causing leakage. I was switched to the Nasal Airpillows P10 yesterday. My problem has been hooking it up. I know it is pretty straight forward but I think part of the face mask tubing is stuck at the end of the main tube. Has anyone had this problem? I'm worried about damaging the hose if I pull too hard. I could bring it in to the sleep clinic but they can't see me for another week. Can anyone help? I've googled the topic to death (which is how I found this board) and reviewed You Tube videos but so far nothing has helped. Thanks for reading!

Best,
Jacqueline
01-09-2015 10:23 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Joedozer Offline

Members

Posts: 11
Joined: Jan 2015

Machine: resmed air10 autoset
Mask Type: Full face mask
Mask Make & Model: F&P simplus
Humidifier: built in
CPAP Pressure: was 18 now 11-20
CPAP Software: ResScan SleepyHead

Other Comments: 18 Pressure Too much all night.Average about 14 now.

Sex: Male
Location: minnesota usa

Post: #2
RE: ClimateLineAir Tubing
pull it off dont think you can hurt it.They are made to interchange.
01-09-2015 10:41 PM
Find all posts by this user Post Reply Quote this message in a reply
Joedozer Offline

Members

Posts: 11
Joined: Jan 2015

Machine: resmed air10 autoset
Mask Type: Full face mask
Mask Make & Model: F&P simplus
Humidifier: built in
CPAP Pressure: was 18 now 11-20
CPAP Software: ResScan SleepyHead

Other Comments: 18 Pressure Too much all night.Average about 14 now.

Sex: Male
Location: minnesota usa

Post: #3
RE: ClimateLineAir Tubing
The end of the climate hose has a rubber end that stays with hose , it has indents that your fingers fit into to wiggle and remove from mask.Hope it helps you.
01-09-2015 10:55 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Crimson Nape Offline

Monitors

Posts: 1,335
Joined: Oct 2014

Machine: ResMed S9 Autoset
Mask Type: Other
Mask Make & Model: P-10 / F&P Simplus / DreamWear
Humidifier: H5i w/Climateline
CPAP Pressure: 8 - EPR 3
CPAP Software: SleepyHead

Other Comments: CMS-50F & 50IW

Sex: Male
Location: Georgia

Post: #4
RE: ClimateLineAir Tubing
For what it's worth, my F&P Simplus came with a hose reducer. It is a gray littler connector that will stick in the hose. It takes some effort for it to come out.

Statistics prove that people who have more birthdays live longer.
01-09-2015 11:14 PM
Find all posts by this user Post Reply Quote this message in a reply
Jacqv21 Offline

Members

Posts: 4
Joined: Jan 2015

Machine: Resmed AirSense10
Mask Type: Full face mask
Mask Make & Model: Unsure
Humidifier: ClimateLineAir
CPAP Pressure: 5-10
CPAP Software: ResScan

Other Comments:

Sex: Female
Location:

Post: #5
RE: ClimateLineAir Tubing
Thanks guys. I found an old post by JCarrera that explained the problem much better. In case anybody else has this problem in the future and finds THIS post I will try to explain better. At the end of the hose is a connector that swivels and is interchangeable with different face masks but not the nasal air pillows. The connector does not appear to come out but that is because just a little bit of plastic tubing peeks over the top of the grey indented rubber part. It seems part of the ClimateLineAir tubing but it's not. It's part of the extra piece. Soooo... when you separate the hose and swivel extension make sure you're not holding on to the hard plastic bit! Thanks everyone!
01-09-2015 11:33 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
trish6hundred Offline

Advisory Members

Posts: 6,452
Joined: May 2012

Machine: Resmed S9 AutoSet for Her
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: H5i Heated Humidifier
CPAP Pressure: 10 - 7-20 Cm H2O
CPAP Software: Not using software

Other Comments: I started CPAP in 2008. Totally blind since birth.

Sex: Female
Location: Missouri, USA

Post: #6
RE: ClimateLineAir Tubing
Hi Jacqv21,
WELCOME! to the forum.!
Glad you were able to figure out how to get your mask and ClimateLine tubing apart.
Much success to you with your CPAP therapy.

trish6hundred
01-09-2015 11:52 PM
Find all posts by this user Post Reply Quote this message in a reply
trish6hundred Offline

Advisory Members

Posts: 6,452
Joined: May 2012

Machine: Resmed S9 AutoSet for Her
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: H5i Heated Humidifier
CPAP Pressure: 10 - 7-20 Cm H2O
CPAP Software: Not using software

Other Comments: I started CPAP in 2008. Totally blind since birth.

Sex: Female
Location: Missouri, USA

Post: #7
RE: ClimateLineAir Tubing
(01-09-2015 10:55 PM)joe johnston Wrote:  The end of the climate hose has a rubber end that stays with hose , it has indents that your fingers fit into to wiggle and remove from mask.Hope it helps you.
Hi joe johnston,
WELCOME! to the forum.!
Much success to you with your CPAP therapy.

trish6hundred
01-10-2015 12:00 AM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
TyroneShoes Offline

Preferred Members-2

Posts: 505
Joined: Oct 2014

Machine: Resmed S9 Autoset
Mask Type: Nasal pillows
Mask Make & Model: AirFit P10
Humidifier: Resmed H5i
CPAP Pressure: 10-14
CPAP Software: SleepyHead

Other Comments:

Sex: Undisclosed
Location:

Post: #8
RE: ClimateLineAir Tubing
Just a simple twisting motion...

I no longer ever disconnect my mask from the hose. The new P10 has the ability to remove the front part for washing...it just clicks in and out.
01-10-2015 12:58 PM
Find all posts by this user Post Reply Quote this message in a reply
Jacqv21 Offline

Members

Posts: 4
Joined: Jan 2015

Machine: Resmed AirSense10
Mask Type: Full face mask
Mask Make & Model: Unsure
Humidifier: ClimateLineAir
CPAP Pressure: 5-10
CPAP Software: ResScan

Other Comments:

Sex: Female
Location:

Post: #9
RE: ClimateLineAir Tubing
Thanks Trish and everybody ;-)
01-10-2015 11:40 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
archangle Online
Wiki Editor
Advisory Members

Posts: 3,163
Joined: Feb 2012

Machine: ResMed S9 AutoSet
Mask Type: Nasal pillows
Mask Make & Model: ResMed Swift FX
Humidifier: ResMed S9 H5i
CPAP Pressure: 16-20
CPAP Software: ResScan SleepyHead EncoreBasic

Other Comments: Happy PAPper

Sex: Undisclosed
Location: USA

Post: #10
RE: ClimateLineAir Tubing
There's a link in my signature line with a hint on how to take the rubber hose off the connector easily.

Get the free SleepyHead software here.
Useful links.
Click here for information on the main alternative to CPAP.
If it's midnight and a DME tells you it's dark outside, go and check it yourself.
01-11-2015 01:38 AM
Find all posts by this user Post Reply Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Tubing size jmayer180 7 297 11-14-2016 11:46 PM
Last Post: Sleepster
  Resmed Climateline tubing smell wenfroed 3 417 09-19-2016 10:03 PM
Last Post: Mosquitobait
  A10 error- tubing blocked check your tubing dwd1249 9 646 07-08-2016 09:33 AM
Last Post: sonicboom
  Clearing rain out from tubing shokk 13 855 07-07-2016 04:21 AM
Last Post: shokk
  Climate line tubing for A10 Autoset Inky1 3 608 03-01-2016 08:27 PM
Last Post: foss
  Tubing Makes A Difference gondolabob 11 1,284 01-28-2016 11:43 AM
Last Post: GPSMapNut
  Heated Tubing? Need your recommendations Night Train 16 2,161 12-01-2015 03:53 PM
Last Post: Night Train

Forum Jump:

Who's Online (Complete List)