Post Reply 
[Equipment]  How to view statistics on M Series Auto CPAP with A-Flex
Author Message
renatae Offline

Preferred Members

Posts: 49
Joined: Oct 2012

Machine: ResMed S9 AutoSet for Her
Mask Type: Nasal pillows
Mask Make & Model: Swift FX Bella Loops
Humidifier: ResMed H5i
CPAP Pressure: 12-17 Mostly stays under 13
CPAP Software: ResScan SleepyHead

Other Comments: Hubby is also a hosehead using Respironics RemStar Pro w/C-flex

Sex: Female
Location: Chicagoland

Post: #1
How to view statistics on M Series Auto CPAP with A-Flex
My hubby has this machine - getting pretty old, and he has not been seeing his doc for follow up, etc.Oh-jeez Wondering if it is possible to view stats on this machine, and if so, how? On the screen, I see setup option, and available here on site are instructions on adjusting settings, but I'm more interested in seeing if we can check the stats.

In addition, the machine has suddenly started spitting in the middle of the night from the humidifier. ??

Thanks for any advice!

To sleep; perchance to dream...
[Image: resmedforher.gif]
[Image: Sleepwellpink1_zps36e39dba.gif]
11-09-2012 04:18 AM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
zonk Offline

Advisory Members

Posts: 7,908
Joined: Feb 2012

Machine: A10 AutoSet
Mask Type: Nasal mask
Mask Make & Model: Activa LT
Humidifier: Integrated /ClimateLineAir
CPAP Pressure: 9/13
CPAP Software: ResScan

Other Comments: CPAP since Nov 2010

Sex: Male
Location: Australia

Post: #2
RE: How to view statistics on M Series Auto CPAP with A-Flex
welcome to the board
just checked the manual which is available by direct download (section two). you need to set the feature: ON - to shows AHI/Leak stats on the screen http://www.apneaboard.com/adjust-cpap-pr...tup-manual

the water in the hose called rainout .... turn down humidity setting a notch or two also you can add a hose cozy which is basically fleece material wrapping which helps insulate the hose
(This post was last modified: 11-09-2012 05:39 AM by zonk.)
11-09-2012 05:05 AM
Find all posts by this user Post Reply Quote this message in a reply
renatae Offline

Preferred Members

Posts: 49
Joined: Oct 2012

Machine: ResMed S9 AutoSet for Her
Mask Type: Nasal pillows
Mask Make & Model: Swift FX Bella Loops
Humidifier: ResMed H5i
CPAP Pressure: 12-17 Mostly stays under 13
CPAP Software: ResScan SleepyHead

Other Comments: Hubby is also a hosehead using Respironics RemStar Pro w/C-flex

Sex: Female
Location: Chicagoland

Post: #3
RE: How to view statistics on M Series Auto CPAP with A-Flex
Thanks so much, zonk! I found a more basic manual for the machine - I must have missed section 2 there. That's just what I was looking forl

The water problem is not in the hose - it's spitting out onto the bedside table - not in terrific amounts - either a 2 cm puddle or a bit of spray - just weird. It's never done this before.

To sleep; perchance to dream...
[Image: resmedforher.gif]
[Image: Sleepwellpink1_zps36e39dba.gif]
11-09-2012 10:48 AM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
trish6hundred Offline

Advisory Members

Posts: 6,450
Joined: May 2012

Machine: Resmed S9 AutoSet for Her
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: H5i Heated Humidifier
CPAP Pressure: 10 - 7-20 Cm H2O
CPAP Software: Not using software

Other Comments: I started CPAP in 2008. Totally blind since birth.

Sex: Female
Location: Missouri, USA

Post: #4
RE: How to view statistics on M Series Auto CPAP with A-Flex
Hi renatae and WELCOME! to the forum.!
As far as your problem with the water spraying out of the M series machine is concerned, I think there are some rubber seals on the water tank (which goes into the humidifier,)that might need to be replaced.
Best of luck to you.

trish6hundred
11-09-2012 03:54 PM
Find all posts by this user Post Reply Quote this message in a reply
renatae Offline

Preferred Members

Posts: 49
Joined: Oct 2012

Machine: ResMed S9 AutoSet for Her
Mask Type: Nasal pillows
Mask Make & Model: Swift FX Bella Loops
Humidifier: ResMed H5i
CPAP Pressure: 12-17 Mostly stays under 13
CPAP Software: ResScan SleepyHead

Other Comments: Hubby is also a hosehead using Respironics RemStar Pro w/C-flex

Sex: Female
Location: Chicagoland

Post: #5
RE: How to view statistics on M Series Auto CPAP with A-Flex
Thanks Thank you, Trish, for the welcome and advice! I really appreciate everyone on this forum and their helping, caring attitudes!

You are probably right about the seals - in fact, that's what my hubby said today. He really needs some replacement things for his unit!



I-love-Apnea-Board

To sleep; perchance to dream...
[Image: resmedforher.gif]
[Image: Sleepwellpink1_zps36e39dba.gif]
(This post was last modified: 11-09-2012 09:56 PM by renatae.)
11-09-2012 09:53 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  philips remstar auto a-flex skylersdad 2 170 11-29-2016 05:47 PM
Last Post: trish6hundred
Question BiPAP vs EPR/Flex etc? SleepyBee 7 275 11-13-2016 08:52 PM
Last Post: Galactus
  [Equipment] Annoying on/off beep on Respironics BIPAP S/T C series rcattell 8 348 11-06-2016 12:07 PM
Last Post: rcattell
  Questions for anyone who has tried Transcend Mini Auto CPAP rdavis 3 243 11-04-2016 06:42 PM
Last Post: Sleeprider
  [CPAP] Setting up this auto a-flex is really intimidating. SierraMadreMe 6 388 10-27-2016 04:25 AM
Last Post: SierraMadreMe
  Flex settings and hypopneas KSMatthew 4 531 10-21-2016 09:47 PM
Last Post: Sleeprider
  Ordered a Auto CPAP / Was diagnosed with Sleep Apnea jakthebomb 15 812 10-18-2016 08:00 AM
Last Post: southerndoc

Forum Jump:

Who's Online (Complete List)