Hello Guest,
Welcome to Apnea Board !As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address. Login or Create an Account
[Equipment] REMStar Pus C-Flex reset
|
05-26-2013, 03:26 PM
RE: REMStar Pus C-Flex reset...
Another good description of a "BRICK," (Ha-Ha-Ha-Ha?)
trish6hundred
05-27-2013, 09:27 PM
RE: REMStar Pus C-Flex reset...
(05-25-2013, 04:26 PM)zonk Wrote:(05-25-2013, 06:37 AM)archangle Wrote: I don't usually comment on typos,what typos? The thread title says, "REMStar Pus C-Flex reset" rather than "REMStar Plus C-Flereset" He was saying that REMstar Pus is a good description of this CPAP machine.
SuperSleeper
Apnea Board Administrator www.ApneaBoard.com INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
DONATE to Apnea Board
Change your own pressure - Get the Clinician Setup Manual for your CPAP here OSCAR - Open Source CPAP Analysis Reporter
05-27-2013, 09:48 PM
RE: REMStar Pus C-Flex reset...
Maybe they don't know what a pus is down under?
Sleepster
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
02-25-2014, 02:17 PM
RE: REMStar Pus C-Flex reset
Clean and reseat the "silicone/rubber sensing piece" works for me. I have a REMstar Pro C-Flex + ... with System-One Heated Humidifier unit. Problem = Service Required. * I removed / detached the humidifier unit from the main unit. * Removed the 2 hex screws on from the bottom of the main unit. * Inside the main unit, I removed the "silicone/rubber sensing piece" and cleaned with water. Look like there was some water-hardness residues on the "silicone sensing piece". That fixed the problem .... THANK YOU !!! THANK YOU !!!
02-25-2014, 04:18 PM
RE: REMStar Pus C-Flex reset
Hi h4ppyb4by,
WELCOME! to the forum.! Glad you were able to fix your machine.
trish6hundred
02-25-2014, 04:34 PM
RE: REMStar Pus C-Flex reset
Okay archangle, that was funny!
As always, YMMV! You do not have to agree or disagree, I am not a professional so my mental meanderings are simply recollections of things from my own life.
PRS1 - Auto - A-Flex x2 - 12.50 - 20 - Humid x2 - Swift FX
03-01-2014, 10:56 PM
RE: REMStar Pus C-Flex reset
Still having the problem. Lowered the humidify from 5 to 3 .... didn't help. The machine runs for 2 or 3 days then same problem "Service Required". I just open up the machine and re-position the silicon/rubber piece ... then it works again. For now, I just leave the 2 screws out for easy open up the machine when I need to "reset" it.
05-12-2014, 10:57 AM
RE: REMStar Pus C-Flex reset
My REMstarPlus M series C-Flex has SIX screws on the bottom (older model?). My machine went out at the worst possible time, I'm out of town for 9 days for my daughter's wedding. In a hotel with my wife and face the prospect of having to sleep on the pull out bed for the next week. I'm going to give your solution a shot as soon as I get (or buy) the proper screw driver. Thanks for at least giving me some hope!
05-12-2014, 08:19 PM
RE: REMStar Pus C-Flex reset
(05-12-2014, 10:57 AM)squid4488 Wrote: My REMstarPlus M series C-Flex has SIX screws on the bottom (older model?). My machine went out at the worst possible time, I'm out of town for 9 days for my daughter's wedding. In a hotel with my wife and face the prospect of having to sleep on the pull out bed for the next week. I'm going to give your solution a shot as soon as I get (or buy) the proper screw driver. Thanks for at least giving me some hope!Hi squid4488, WELCOME! to the forum.! That's a bummer, what a bad time for your machine to go out on you; hopefully you can get it to work for you. Best of luck.
trish6hundred
05-27-2014, 08:51 PM
RE: REMStar Pus C-Flex reset
As did others, I took off the cover, removed the circuit board, removed the three hole sensor gasket. Then reassembled and it is working, for how long I am not sure.
But sheesh, feel asleep in an afternoon meeting today! Its been two years since that happened. Oh and the machine is 2 years and 3 months old, so just out of warranty of course. |
« Next Oldest | Next Newest »
|
Possibly Related Threads... | |||||
Thread | Author | Replies | Views | Last Post | |
Picked up ResMed 10 today, concerned about ability to reset flow rates | NewlyDiagnosed | 10 | 237 |
04-08-2024, 07:39 AM Last Post: NewlyDiagnosed |
|
Is my Philips Remstar Pro System One working? | alanbc | 11 | 478 |
03-13-2024, 11:41 AM Last Post: alanbc |
|
[Equipment] Seeking advice for reset of time zone | richapple | 0 | 213 |
02-03-2024, 11:43 AM Last Post: richapple |
|
[CPAP] Reset motor run hours after new motor | djforrestidaho | 9 | 906 |
12-06-2023, 04:19 PM Last Post: srlevine1 |
|
Remstar -> DS 1(new foam) | mw1655 | 0 | 273 |
11-29-2023, 05:54 AM Last Post: mw1655 |
|
Any one know how reset the Resmed Airsense 10? | hs8738 | 8 | 28,026 |
11-24-2023, 04:48 PM Last Post: SarcasticDave94 |
|
Apex XT Auto CPAP - Error 003 - Factory Reset? | zephyr325 | 0 | 881 |
05-24-2023, 03:52 PM Last Post: zephyr325 |