Post Reply 
[Equipment] Trouble reading detailed data
Author Message
doddsie Offline

Members

Posts: 4
Joined: Dec 2013

Machine: ResMed S9 AutoSet
Mask Type: Full face mask
Mask Make & Model: FlexiFit HC431
Humidifier: S9 Series H5i
CPAP Pressure: 10-18
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Los Gatos, CA, USA

Post: #1
Trouble reading detailed data
Hi All,

I am new to this forum!

I recently got a Resmed S9 AutoSet because I am interested in viewing the detailed information using SleepyHead.

I have somehow successfully downloaded and imported 2 nights of data into SleepyHead however each morning however, there is confusion as to how I get to the detailed data.

What I have been doing is, when I wake up, I:
  • Turn off S9 to stop the CPAP
  • Pop the SD card out
  • Insert card into my computers SD reader (lock card first)
  • Import into SleepyHead

When I do this first thing in the morning it seems that the detailed data has not been written to the SD card yet, because I am only able to see the summary type information. It is matching what is on the S9. So some data IS getting imported?

Then, I spend about an hour or so trying to figure out how to get the detailed data and at some point the data is on the card. I reboot the S9, copy the data to the computer before inputting, ...

Does anyone have a clue? Is there something I am supposed to do before pulling the SD card out of the S9?

Thanks!
Dave
(This post was last modified: 12-16-2013 01:15 PM by doddsie.)
12-16-2013 01:07 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
trish6hundred Offline

Advisory Members

Posts: 6,450
Joined: May 2012

Machine: Resmed S9 AutoSet for Her
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: H5i Heated Humidifier
CPAP Pressure: 10 - 7-20 Cm H2O
CPAP Software: Not using software

Other Comments: I started CPAP in 2008. Totally blind since birth.

Sex: Female
Location: Missouri, USA

Post: #2
RE: Trouble reading detailed data
Hi doddsie,
WELCOME! to the forum.!
Hang in there for answers to your data questions and best of luck to you.

trish6hundred
12-16-2013 04:04 PM
Find all posts by this user Post Reply Quote this message in a reply
cbramsey Offline

Advisory Members

Posts: 900
Joined: Mar 2012

Machine: ResMed S9 Autoset
Mask Type: Nasal mask
Mask Make & Model: ResMed Mirage FX
Humidifier: ResMed H5i with ClimateLine
CPAP Pressure: 6 - 12
CPAP Software: ResScan

Other Comments: Supreme Overlord of Web Darkness

Sex: Male
Location: NC, USA

Post: #3
RE: Trouble reading detailed data
When you open the ResScan software after inserting the SD card into the reader, a pop-up window will show up. It will give you options to download All Summary Data only (This is the default choice.) and All Data and a pull down menu showing the number of the most recent detailed data sessions. You will need to choose this option.

What I have described is on page 12 of the ResScan Clinicians Manual which is installed as well when you install ResScan.

Try that and see if it helps.

Sleep-well

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
12-16-2013 04:20 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
me50 Offline

Advisory Members

Posts: 2,559
Joined: Aug 2013

Machine: resmed S9 VPAP Auto
Mask Type: Nasal mask
Mask Make & Model: Wisp and Silicone Head gear
Humidifier: resmed H5i
CPAP Pressure: 18/8
CPAP Software: SleepyHead

Other Comments:

Sex: Undisclosed
Location: USA

Post: #4
RE: Trouble reading detailed data
doddsie are you looking at the daily tab? If not, once you have imported to SleepyHead, click on the daily tab. It should show some graphs on the right side of the screen.
12-16-2013 04:31 PM
Find all posts by this user Post Reply Quote this message in a reply
PaulaO2 Offline
Wiki Editor
Moderators

Posts: 8,067
Joined: Feb 2012

Machine: S9 Autoset
Mask Type: Full face mask
Mask Make & Model: F&P Simplus
Humidifier: H5i
CPAP Pressure: 14-20
CPAP Software: SleepyHead

Other Comments: Ehlers-Danlos Syndrome, Hypermobility Type; chronic sarcasm

Sex: Undisclosed
Location: western NC, USA

Post: #5
RE: Trouble reading detailed data
If you are removing the card immediately after waking up, you may not be giving the machine time to finish writing to the card. I'm not sure of how much time it needs, however. I usually wait at least a half hour, just to be safe.

Also, if you are sleeping past what the machine believes is noon, there won't be any data, or limited data, because at noon, it starts the next day. I've been tricked by this numerous times. Just check the time on the machine against your local time. If you need to reset the machine's clock, you can find out how here:
http://www.apneaboard.com/wiki/index.php?title=Setting_the_clock

PaulaO2
Apnea Board Moderator
www.ApneaBoard.com


Breathe deeply and count to zen.

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
12-16-2013 07:38 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
doddsie Offline

Members

Posts: 4
Joined: Dec 2013

Machine: ResMed S9 AutoSet
Mask Type: Full face mask
Mask Make & Model: FlexiFit HC431
Humidifier: S9 Series H5i
CPAP Pressure: 10-18
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Los Gatos, CA, USA

Post: #6
RE: Trouble reading detailed data
Thanks PaulaO2 and everyone else for the answers. I will try to wait at least a half hour before popping the card out.

I am SleepyHead and am trying to view the Daily Tab, however there is no data there.

Let's hope that waiting a while will allow the data to be written.

Are there any other steps for pulling the card out? Are you turning the S9 off by pressing and holding the on/off switching? Or just popping the sd card out with no other steps?

It certainly would be nice to know when the card has had the data written to it!

Thanks,
Dave



(12-16-2013 07:38 PM)PaulaO2 Wrote:  If you are removing the card immediately after waking up, you may not be giving the machine time to finish writing to the card. I'm not sure of how much time it needs, however. I usually wait at least a half hour, just to be safe.

Also, if you are sleeping past what the machine believes is noon, there won't be any data, or limited data, because at noon, it starts the next day. I've been tricked by this numerous times. Just check the time on the machine against your local time. If you need to reset the machine's clock, you can find out how here:
12-16-2013 08:14 PM
Find all posts by this user Post Reply Quote this message in a reply
me50 Offline

Advisory Members

Posts: 2,559
Joined: Aug 2013

Machine: resmed S9 VPAP Auto
Mask Type: Nasal mask
Mask Make & Model: Wisp and Silicone Head gear
Humidifier: resmed H5i
CPAP Pressure: 18/8
CPAP Software: SleepyHead

Other Comments:

Sex: Undisclosed
Location: USA

Post: #7
RE: Trouble reading detailed data
I haven't turned my machine off before taking the card out. I just lock it, put it in the SD slot on my laptop, open SH, select user, import from SD card and when it is finished, I click on the daily tab and my data is there. I am not sure how to help you because I haven't ever not had data there for the night before.
12-16-2013 08:19 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
robysue Offline
Wiki Editor
Advisory Members

Posts: 1,240
Joined: Oct 2013

Machine: PR Dreamstation BiPAP Auto
Mask Type: Nasal pillows
Mask Make & Model: Swift FX
Humidifier: PR Dreamstation humidfier
CPAP Pressure: min EPAP = 4; max IPAP = 9;
CPAP Software: SleepyHead EncoreBasic EncorePro

Other Comments: Papping since September 2010

Sex: Female
Location: Buffalo, NY

Post: #8
RE: Trouble reading detailed data
doddsie,

Just wanting to eliminate obvious problems: You are sure you are using an S9 AutoSet and not an S9 Auto Escape?

SleepyHead doesn't manage to deal with the (limited) data on the Auto Escape because SH needs the detailed data that the Auto Escape does not record in order to display the data correctly.

If you are using an S9 AutoSet, then it's also important to make sure that the Sleep Quality setting is set to On instead of Usage. When the Sleep Quality is set to Usage, not all the data is recorded to the SD card.
(This post was last modified: 12-16-2013 09:32 PM by robysue.)
12-16-2013 09:30 PM
Find all posts by this user Post Reply Quote this message in a reply
zonk Offline

Advisory Members

Posts: 7,908
Joined: Feb 2012

Machine: A10 AutoSet
Mask Type: Nasal mask
Mask Make & Model: Activa LT
Humidifier: Integrated /ClimateLineAir
CPAP Pressure: 9/13
CPAP Software: ResScan

Other Comments: CPAP since Nov 2010

Sex: Male
Location: Australia

Post: #9
RE: Trouble reading detailed data
(12-16-2013 09:30 PM)robysue Wrote:  When the Sleep Quality is set to Usage, not all the data is recorded to the SD card.
What Robysue said. S9 Sleep Quality default setting set to usage
Model name printed next to on/off button
12-16-2013 11:00 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
doddsie Offline

Members

Posts: 4
Joined: Dec 2013

Machine: ResMed S9 AutoSet
Mask Type: Full face mask
Mask Make & Model: FlexiFit HC431
Humidifier: S9 Series H5i
CPAP Pressure: 10-18
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Los Gatos, CA, USA

Post: #10
RE: Trouble reading detailed data
Again,
Thanks all for the replies.

I definately have the AutoSet version as I have seen detailed data. I think that there is something that I must be doing differently. I also checked the Sleep Quality and it is set to ON. And made sure the time/date were set correctly.

How long are others waiting before they remove the SD card from the S9? I was so excited to see my results this morning I popped it out as soon as I turned off the CPAP.

Will let you all know how it goes tomorrow!

Thanks,
Dave


(12-16-2013 11:00 PM)zonk Wrote:  
(12-16-2013 09:30 PM)robysue Wrote:  When the Sleep Quality is set to Usage, not all the data is recorded to the SD card.
What Robysue said. S9 Sleep Quality default setting set to usage
Model name printed next to on/off button
12-17-2013 12:47 AM
Find all posts by this user Post Reply Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  New User Having Trouble Staying Asleep and more SnoreGalore 9 517 12-06-2016 08:00 PM
Last Post: SnoreGalore
  [Equipment] SD card reading tim52160 15 1,226 09-27-2016 08:14 PM
Last Post: pjfollyfarm
  help reading SleepyHead data charts JaneAM 2 416 09-26-2016 10:27 AM
Last Post: Crimson Nape
  Having trouble with new mask rich2905 9 436 09-03-2016 03:44 AM
Last Post: rich2905
  Sleepyhead data vs. Doctor's data Daisylouu 8 1,404 09-01-2016 06:10 PM
Last Post: eseedhouse
Arrow [Diagnosis] Am I reading this right? Kakesim 7 448 08-30-2016 06:40 PM
Last Post: chill
  Trouble with P10 mattmill 17 710 08-04-2016 08:30 PM
Last Post: Mosquitobait

Forum Jump:

Who's Online (Complete List)