Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

[Equipment] Viscious cycle of increased pressure -> more leak -> response of more pressure
#1
I have an autosense 10 and nasal prongs.  I have tried to persist with it but I can't sleep with it. I find that I start out with a good seal but once I change positions even minorly, more air leaks out around the prongs.  I have tried different sizes and 2 different brands.  Even if I don't shift position, I find that the pressure builds up gradually and then a constant leak occurs.  The machine ramps up to compensate and then even more air flows out.  

Any suggestions?  I am not a mouth breather but wondering if I should consider some type of mask.
Post Reply Post Reply
#2
I have a P10 but have not used it much.  I use an F&P Eson (now the Eson 2 is out) at 15 with no noticeable leaks unless I roll around in bed and dislodge it.
Post Reply Post Reply
#3
I prefer the P10, but I do get slight leakage.
Every few weeks, I'll get irritation on one of my nostrils and will switch to a nasal mask (Respironics Wisp).
It is not as comfortable, which is why I don't stick with it, but my leakage is extremely low... shows as zero on the Resmed "MyAir" charts, but there is something on the Sleepyhead graphs.
-- Rich
Download SleepyHead here
Organize SleepyHead Data
Post SleepyHead Data from Imgur

INFORMATION ON FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.

Post Reply Post Reply


#4
Wink 
Do not  use your S10 at max pressure (20) use 3cm/H2O up your's medial necessary pressure (7cm/H2O) programable in ResScan software
Post Reply Post Reply
#5
(09-16-2017, 08:29 AM)rdreher99 Wrote: Do not  use your S10 at max pressure (20) use 3cm/H2O up your's medial necessary pressure (7cm/H2O) programable in ResScan software


Hi and Welcome to the forum!

It looks like the OP settings are 5cm and ramping to 15cm. Or he is using auto 5-15. The lowest setting is 4cm.
These settings may or may not be optimal, which is why we usually ask for data before making recommendations.

A setting that works for one person isn't always best for another.
OpalRose
Apnea Board Moderator
www.ApneaBoard.com

How to Organize and Post ScreenShots

http://sleep.tnet.com/resources/sleepyhead/shorganize
https://sleep.tnet.com/reference/tips/imgur

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.




Post Reply Post Reply
#6
(09-15-2017, 11:11 PM)3mp0w3r Wrote: I have an autosense 10 and nasal prongs.  I have tried to persist with it but I can't sleep with it.  I find that I start out with a good seal but once I change positions even minorly, more air leaks out around the prongs.  I have tried different sizes and 2 different brands.  Even if I don't shift position, I find that the pressure builds up gradually and then a constant leak occurs.  The machine ramps up to compensate and then even more air flows out.  

Any suggestions?  I am not a mouth breather but wondering if I should consider some type of mask.

If you have given the nasal pillow masks a try and experiencing leaks, the pillow may be too small. It should not be inserted into the nostril but sit just below (slightly inserted).

If you can't get past mouth breathing, then a full face mask may be in order.

Masks are very individual, and you may have to try something else.

When you say "more air flows out", what do you mean? The venting is in the front of the P10, and is very quiet. This is normal. If you have air leaking from around the nostrils, then the fit is wrong.

Many folk here use high pressures with a nasal pillow mask with no problems.

Also, your pressure settings may not be optimal for you. We can help zero in on that if you post some data. We can also take a look at the leak rate.

Follow the tutorials in my signature line.
OpalRose
Apnea Board Moderator
www.ApneaBoard.com

How to Organize and Post ScreenShots

http://sleep.tnet.com/resources/sleepyhead/shorganize
https://sleep.tnet.com/reference/tips/imgur

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.




Post Reply Post Reply




Possibly Related Threads...
Thread Author Replies Views Last Post
  Advise a New Guy [on high pressure readings] zzzZorro 30 477 2 hours ago
Last Post: Sleeprider
  How to work out the correct pressure required ? BHappy 5 139 Yesterday, 12:09 AM
Last Post: bonjour
  Latest SH Chart, wondering about Leak Rate pcplus2 5 123 09-22-2017, 09:56 AM
Last Post: bonjour
  Help Understanding Leak Rate & Statistics Hojo 2 147 09-20-2017, 05:29 PM
Last Post: Walla Walla
  [CPAP] right amount of pressure Healthkares 4 121 09-18-2017, 03:38 PM
Last Post: trish6hundred
Question [Pressure] New ResMed Airsense 10 Pressure Problem spookyac47 5 229 09-16-2017, 03:44 PM
Last Post: trish6hundred
  How do I know if pressure is too high? gimmedaREM 8 286 09-15-2017, 06:03 PM
Last Post: trish6hundred

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.