Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Even time
#1
is it possible to adjust the event time in the software to see event below the 10 second threshold
Post Reply Post Reply
#2
Short answer, no. It would require a change in the firmware.


Dude
Post Reply Post Reply
#3
(02-23-2016, 10:34 AM)surferdude2 Wrote: Short answer, no. It would require a change in the firmware.


Dude

Do we know what the measurement accuracy of the test. Is it 10 Sec plus or minus 1 ? or worse than that.
Post Reply Post Reply


#4
You can extrapolate that from expanding several of the flow graphs but I doubt it's worth the time. I assume that is less a problem than actually determining the reason for the lapse in flow. The machines do a good enough job and that's good enough until something better emerges. As is often mentioned, the bottom line isn't how low the numbers are below the <5 marker but how you feel.

Dude
Post Reply Post Reply
#5
I seem to remember that in Sleepyhead there are 2 user definable flags that one can set for a definable time period. I think they are UF1 and UF2
Post Reply Post Reply
#6
(02-23-2016, 10:19 AM)0rangebear Wrote: is it possible to adjust the event time in the software to see event below the 10 second threshold

Yes, this can be done in SleepyHead. Go to File | Preferences | CPAP | Custom CPAP User Event Flagging. It allows you to set two user flags, and for each one you can set a threshold flow restriction and duration (eg 75% for 8 seconds).

DeepBreathing
Apnea Board Moderator
www.ApneaBoard.com


Bed

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply


#7
(02-23-2016, 11:29 PM)DeepBreathing Wrote:
(02-23-2016, 10:19 AM)0rangebear Wrote: is it possible to adjust the event time in the software to see event below the 10 second threshold

Yes, this can be done in SleepyHead. Go to File | Preferences | CPAP | Custom CPAP User Event Flagging. It allows you to set two user flags, and for each one you can set a threshold flow restriction and duration (eg 75% for 8 seconds).

coolThanks
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Idea CMS50D+ Add date and time to SPO2 file adrinef 2 364 06-20-2017, 08:46 AM
Last Post: adrinef
  Key response time on my IPad Rcgop 5 297 06-19-2017, 01:05 AM
Last Post: TBMx
  DreamMapper update, wrong time no new data. MrEGuy 7 4,325 04-25-2017, 07:57 PM
Last Post: mkov608
Surprised Confused on oximeter real time usage on sleepyhead triciagalexander 10 674 02-10-2017, 11:26 PM
Last Post: triciagalexander
  Cannot save CMS50D+ data after entering time on Mac mjs31 3 385 01-01-2017, 06:29 PM
Last Post: chill
  FlashPAP - connection time out. Tassie tone 4 521 09-23-2016, 09:14 PM
Last Post: sonicboom
Question SH Time at Pressure graph question Snowbird47 2 668 05-24-2016, 08:17 AM
Last Post: Snowbird47

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.