Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account

New Posts   Today's Posts

Fisher Pakel Error Code E2
RE: Fisher Pakel Error Code E2
Moisture issue. Water got inside your unit - maybe fro traveling with an humidifier not properly emptied. Just open the unit (6 screws under the unit) and use a hairdryer to dry the circuit boards. Replug the unit and voilà, problem solved.
Post Reply Post Reply

Donate to Apnea Board  
RE: Fisher Pakel Error Code E2
Hi sleepless in ottawa, WELCOME! to the forum.!
Post Reply Post Reply
RE: Fisher Pakel Error Code E2
2019 this reply is a little late but their may be people out their like us that still use this model machine so I hope this may help someone. My husband tipped over his sleepstyle 600 while sleeping last night. It did not fall off the nightstand and he stood it right back up as soon as it happened. When he turned it back on we got E2 error code.  I removed all attached equipment and power plug, then turned the machine upside down. Water did come out of the machine onto the nightstand. I plugged back in, still E2 error. Then I let the machine sit for about 10 min. upside down. Still E2 error. I then used a blow dryer on LOW into each hose/water connection chamber. Without attaching any equipment I plugged it back in and it began to run properly. I then put the water reservoir back in and attached the heated hose. Again E2 error. I removed the hose, no error. I then used the blow dryer on LOW on the heated hose for just about a minute. Both ends felt dry. I attached back on the machine and everything appears to running correctly. I have it in the So Clean right now and will post more tomorrow if we find any complications tonight with the machine. Thank You Apenea Board for having this helpful blog to get answers to our questions.
Post Reply Post Reply
RE: Fisher Pakel Error Code E2
Ignore the error codes.  After being advised to take my personal CPAP to the Hospital and having run it non stop for 2 ays it overheated and dried out the bearing.  The noise you hear is the motor vibrating but failing to spin.  Don't be afraid to completely disassemble it after unplugging everything from the wall and the circuit board.  Take off the hose/motor vortex housing and underneath pour some vegetable oil in the shaft housing.  Let it sit a while.  Then plug the board back in while still disassembled and turn the rocker switch on and off until the motor spins up.  It will be slow at first and will immediately be back to normal.  Leave it disassembled and operate it a few times over a few days so the excess oil can be expelled.  Then reassemble it.  I made the mistake of using PBLASTER penetrating oil so I'll have to run mine a week or so before the odor disipates but hey, it was my spare and I thought it was doomed so I'm good!
Post Reply Post Reply

Donate to Apnea Board  

Possibly Related Threads...
Thread Author Replies Views Last Post
Sad [CPAP] Res Med S9 help! Error: Settings reset to default values, please contact service pr dexter020281 19 20,774 05-17-2020, 01:46 AM
Last Post: njhaveman
  My experiences with Fisher & Paykel ESON2 Nose Mask braindead 18 770 05-13-2020, 10:44 AM
Last Post: Smileyman
  DreamStation Error 01509 spacewrench 3 366 04-15-2020, 09:12 AM
Last Post: Sleeprider
Question [Equipment] SmartStart not starting and "Tube blocked" error fasantana 4 280 03-04-2020, 08:49 AM
Last Post: 3rdMarDiv
  Resmed AS10 "tube is blocked" error Charlie Sue 3 261 02-21-2020, 08:30 PM
Last Post: Charlie Sue
Angry error code 19 fireleg 3 303 02-19-2020, 10:58 PM
Last Post: Dormeo
Sad Help please !! my remstar lite has a 32 error and I can't sleep! Jhonn stark 2 176 02-07-2020, 10:07 AM
Last Post: Jhonn stark

New Posts   Today's Posts

About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.