Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

FlashAir Problem?
#1
FlashAir Problem?
I have a FlashAir W-02 16gb card for my A10 Autoset. Normally it reads properly in station mode. Recently however, the card has not been findable by FlashPAP in the mornings when I go to download my data. I have to either remove and reinsert the card or power cycle the machine.

Anyone have a suggested fix for this?

Thanks,
Dave
Post Reply Post Reply
#2
RE: FlashAir Problem?
change the timeout value to 0. Think the default is 30000 or something

APPAUTOTIME=0

https://flashair-developers.com/en/docum...pi/config/
هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Tongue Suck Technique for prevention of mouth breathing:
  • Place your tongue behind your front teeth on the roof of your mouth
  • let your tongue fill the space between the upper molars
  • gently suck to form a light vacuum

Practising during the day can help you to keep it at night

هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Post Reply Post Reply
#3
RE: FlashAir Problem?
(07-20-2015, 02:18 PM)DariaVader Wrote: change the timeout value to 0. Think the default is 30000 or something

APPAUTOTIME=0

https://flashair-developers.com/en/docum...pi/config/

Thanks, I've tried that without success. Here's my config:

[Vendor]

CIPATH=/DCIM/100__TSB/FA000001.JPG
APPMODE=5
APPNAME=FlashAir
APPSSID=ParkerHome 2
APPNETWORKKEY=**********************************
VERSION=FA9CAW3AW3.00.00
CID=02544d535731364731d5d7737900f301
PRODUCT=FlashAir
VENDOR=TOSHIBA
MASTERCODE=1234567890AB
LOCK=1
FORMATSETMODE=1
APPINFO=0000000000000000
APPAUTOTIME=0
STA_RETRY_CT=0
NOISE_CANCEL=0

Dave
Post Reply Post Reply
#4
RE: FlashAir Problem?
I have the S9 Autoset. Perhaps it lacks some of the power saving "features" of the A10... As you know, the flashair gets power to be on from the device it is plugged into.


[Vendor]

CIPATH=/DCIM/100__TSB/FA000001.JPG
VERSION=F19BAW3AW2.00.03
CID=02544d535731364708dd306c7800e601
PRODUCT=FlashAir
VENDOR=TOSHIBA
APPNAME=flashair
WEBDAV=0
TIMEZONE=-28
APPSSID=DARIANET
APPNETWORKKEY=*********
APPMODE=5
APPAUTOTIME=0
DNSMODE=1
LOCK=1
UPLOAD=1
هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Tongue Suck Technique for prevention of mouth breathing:
  • Place your tongue behind your front teeth on the roof of your mouth
  • let your tongue fill the space between the upper molars
  • gently suck to form a light vacuum

Practising during the day can help you to keep it at night

هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Post Reply Post Reply
#5
RE: FlashAir Problem?
Something else to try....

https://sleep.tnet.com/resources/sleepma...lashairfix Wrote:FlashAir Fix for Close Signal Issues

So my CPAP is about 4-1/2ft from the AP... like really close.

Over the weeks, I would not be able to communicate with it even though the AP was showing 60% signal.

After the course of a week or so, I tried a few things but most of the time, the best I could do was get to FlashAir to bounce off the AP (100% for a few seconds.. then gone.. repeat).

Thomas gave me a tip which is supposed to help when the FlashAir is too close to the AP...

Add to the CONFIG file on the FlashAir the following line:

NOISE_CANCEL=2

And that fixed my problem so far for more than 3 days straight.

I would imagine that most have their CPAP machines a bit further away from the AP that I do, so you might not need this "fix". But if you having the same problem, you might give it a try.
هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Tongue Suck Technique for prevention of mouth breathing:
  • Place your tongue behind your front teeth on the roof of your mouth
  • let your tongue fill the space between the upper molars
  • gently suck to form a light vacuum

Practising during the day can help you to keep it at night

هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Post Reply Post Reply
#6
RE: FlashAir Problem?
My AP is about 20 feet away through 2 walls, but can't hurt to try!

Thanks!
Post Reply Post Reply
#7
RE: FlashAir Problem?
I think it is more likely that the A10 is "green" and is not powering the flashair sufficiently to keep it online, but idk. Not likely to be "noise" at that distance, IMO. This might be the first time I am happy I got the older S9 rather than the A10 Big Grin
هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Tongue Suck Technique for prevention of mouth breathing:
  • Place your tongue behind your front teeth on the roof of your mouth
  • let your tongue fill the space between the upper molars
  • gently suck to form a light vacuum

Practising during the day can help you to keep it at night

هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه هههههه  هههههه
Post Reply Post Reply
#8
RE: FlashAir Problem?
I don't know - seems to stay up during the day - I've been hitting it with FlashPAP off and on to see if it has gone away; it has not, and I know my A10 is in powersaving mode.

We'll see what happens in the AM!

Thanks again,
Dave
Post Reply Post Reply
#9
RE: FlashAir Problem?
I occasionally have that issue after I stop using the machine and try to download the data. There is no rhythm or reason for it and it doesn't happen every day. I do notice that when I have a power failure (however brief) I have to reinsert the card to connect it with the network again. Do you have your router set to cycle off/on during the night?
Using FlashAir W-03 SD card in machine. You can download your data through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie

Stick it to the man, Download OSCAR and take back control of your data!

Thanks Ian. Like I didn't have enough Honey-Do projects to tackle. Mornincoffee
Post Reply Post Reply
#10
RE: FlashAir Problem?
No, my router and CPAP are both on UPS supplies, actually. Enough to ride out any outage of an hour and a half or less.
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  AirFit F30i Mask Problem OldTeacher 22 4,562 03-23-2024, 03:23 PM
Last Post: ButtonNoseBarbie
  [CPAP] ResMed Air Sense 10 Auto Off Problem Buddie43 19 26,328 03-05-2024, 10:50 PM
Last Post: Ailyhsaun
  Are these flow limits my problem? k888 87 5,466 02-26-2024, 12:02 PM
Last Post: k888
  [Treatment] Are leaks the problem or do I need BIPAP? TiredDude 3 331 02-22-2024, 07:52 PM
Last Post: Sleeprider
  [CPAP] Is my leak rate a problem? Kevstuf 5 550 02-08-2024, 10:25 AM
Last Post: Kevstuf
  If nasal congestion is a problem, will this show in my AHI? canigetawitness1992 4 391 01-29-2024, 09:20 PM
Last Post: RNeil
  [Equipment] ResMed S9 Elite CPAP – Climate hose problem drewb6111 2 228 01-28-2024, 08:24 PM
Last Post: drewb6111


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.