Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Help with settings
#1
My water level never goes down on my humidifier and this morning I noticed the heater was not warm when I removed the water chamber. I checked my settings and the humidity level is 4 however under reminders it reads mask off,water tub off,tube off and filter off. Please explain this option in clinicians menu and could this be the problem.
Thanks!!
Post Reply Post Reply
#2
These are warning notification options.
______________________
Useful Links -or- When All Else Fails:
Posting SleepyHead Charts in 5 Easy Steps
Robysue's Beginner's Guide to Sleepyhead
Apnea Helpful Tips
Post Reply Post Reply
#3
When you are checking the hot plate under the chamber do it soon after you turn the PAP off because the plate cools down quickly.
if you can't decide then you don't have enough data.
Post Reply Post Reply


#4
(08-30-2015, 09:40 AM)MobileBasset Wrote: When you are checking the hot plate under the chamber do it soon after you turn the PAP off because the plate cools down quickly.

Yes I put my hand on the underside of the water chamber (it was cool) so I reached in to feel the plate and it was also cool!
Post Reply Post Reply
#5
(08-30-2015, 08:06 AM)Judy1843 Wrote: I checked my settings and the humidity level is 4 however under reminders it reads mask off,water tub off,tube off and filter off. Please explain this option in clinicians menu and could this be the problem.
Thanks!!

Reminders are just that, reminders. These are settings to remind you when it is time to replace your mask, tub, tube, and filter.

For each of these, the settings are Off / 1-24 months in 1 month increments.


Using FlashAir W-03 SD card in machine. Access through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie

Post Reply Post Reply
#6
(08-30-2015, 09:59 AM)Judy1843 Wrote:
(08-30-2015, 09:40 AM)MobileBasset Wrote: When you are checking the hot plate under the chamber do it soon after you turn the PAP off because the plate cools down quickly.

Yes I put my hand on the underside of the water chamber (it was cool) so I reached in to feel the plate and it was also cool!

In the user menu options near the bottom there is an option to Run Warmup.
You should see the symbol in the upper right of the screen flashing. It looks like three vertical wavy lines. Imaged attached below.

Off hand I don't recall how long it runs but the plate should be warm after a minute.


Attached Files Image(s)
   


Using FlashAir W-03 SD card in machine. Access through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie

Post Reply Post Reply


#7
(08-30-2015, 10:37 AM)AlanE Wrote:
(08-30-2015, 09:59 AM)Judy1843 Wrote:
(08-30-2015, 09:40 AM)MobileBasset Wrote: When you are checking the hot plate under the chamber do it soon after you turn the PAP off because the plate cools down quickly.

Yes I put my hand on the underside of the water chamber (it was cool) so I reached in to feel the plate and it was also cool!

In the user menu options near the bottom there is an option to Run Warmup.
You should see the symbol in the upper right of the screen flashing. It looks like three vertical wavy lines. Imaged attached below.

Off hand I don't recall how long it runs but the plate should be warm after a minute.

Ok yes I did push run warm up and it did heat up. Do I need to do this every night or does wa up automatically?
Post Reply Post Reply
#8
In the my options screen, set climate control and tube temp to auto, that should keep you from having to run the "warm up".

If your essentials plus option is not turned on, then you would go to the clinical menu to make the same changes.

(08-30-2015, 10:52 AM)Judy1843 Wrote:
(08-30-2015, 10:37 AM)AlanE Wrote:
(08-30-2015, 09:59 AM)Judy1843 Wrote: Yes I put my hand on the underside of the water chamber (it was cool) so I reached in to feel the plate and it was also cool!

In the user menu options near the bottom there is an option to Run Warmup.
You should see the symbol in the upper right of the screen flashing. It looks like three vertical wavy lines. Imaged attached below.

Off hand I don't recall how long it runs but the plate should be warm after a minute.

Ok yes I did push run warm up and it did heat up. Do I need to do this every night or does wa up automatically?

Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Constant Air the same even when i change settings blackhawk2737303 6 234 12-11-2017, 04:16 PM
Last Post: Sleeprider
  PS settings RLSdss 18 453 11-29-2017, 03:14 PM
Last Post: SuperSleeper
  [Pressure] Aircurve 10 VAuto settings recommendations Keith R 11 611 11-19-2017, 04:52 PM
Last Post: Keith R
  Some questions [leakage & proper settings] dhammond 5 316 11-19-2017, 11:24 AM
Last Post: nappyhair2
  Need help with pressure settings readyforsleep 14 717 11-18-2017, 12:52 PM
Last Post: Sleeprider
  Older Machines With PS & EPAP Settings? Greggory 8 195 11-15-2017, 06:55 PM
Last Post: Greggory
  PR System One Mask Resistance Settings sharkcity 18 18,843 11-02-2017, 01:42 PM
Last Post: Raymond Hallett

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.