Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Hissing Problem with Eson mask/tube connector
#11
Eson is what I use and my wife.
I've had several scheduled replacements.
The Eason is as quiet as the grave.

If you mean it's hissing at the ball joint that lets the connection swivel it shouldn't make a sound.

Just make sure the little grey insert that goes into your hose end has the flared end toward the mask connector.

If it is and hissing its a bad mask frame. Make em replace it.
Post Reply Post Reply
#12
(12-31-2016, 06:20 PM)Southerngent1 Wrote: Ockrocket,

You are correct that I have the same problem with leakage on one side of my mask or through the front filter when exhaling strongly. However at the connection point of the tube at the tube filter to my mask I am able to turn my mask assembly 360 degrees with ease. This is where I hear the hissing/air flow.

I am also trying to learn to keep my mask down further on my face which seems to help. However, the extra sound is aggravating as it happens almost every time I turn over and my tube slides out of a perfect perpendicular position.

The elbow connection is supposed to rotate through 360 deg., but it shouldn't leak air to any real extent.


(12-31-2016, 07:53 PM)Beej Wrote: I believe those may be mask vents so you don't suffocate if the machine turns off (power outage, machine failure).

An option which might help is a white nose generator. This is a constant sound just loud enough to mask intermittent sound, and thus lets you ignore what is happening. I picked up an inexpensive one at Amazon.

The Eson mask has a good sized vent with a filter on the elbow connector, you can breathe with relative ease when the machine is off (every night I put my mask on, with the hose connected, before turning my Dreamstation CPAP machine on)
Post Reply Post Reply
#13
Is a bad mask frame common? And yes, the flared end is at my mask, the non-flared going into my machine.
Post Reply Post Reply


#14
Hi Southergent1,
WELCOME! to the forum.!
Good luck figuring out your mask problem and also with your CPAP therapy, hang in there for more responses to your post.
trish6hundred
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  What's the problem? slaterslater 23 555 Yesterday, 10:46 PM
Last Post: slaterslater
  Cleaning Climate-control tube on ResMed Air Sense 10 GL Bishop 28 17,249 Yesterday, 05:52 PM
Last Post: Walla Walla
  Advice Needed- Problem With Recording on the CMS 50D + Oximeter nico08 3 73 08-18-2017, 11:06 PM
Last Post: PaulaO2
  [split] Take charge of your therapy - Heated tube Kathy123 8 354 08-13-2017, 08:30 PM
Last Post: Walla Walla
  Philips Dreamstation with Nuance Pro mask - connector? mkarnofel 2 162 08-02-2017, 02:19 PM
Last Post: PaulaO2
  Problem with my level of AI WilliamVasquez 3 179 07-27-2017, 04:20 PM
Last Post: WilliamVasquez
  Devillbis Smartlink Problem jsielke 1 125 07-26-2017, 09:51 AM
Last Post: jsielke

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.