Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Leak rate (and AHI)
#1
I’m using a apex 220 FB mask. 
Average leak- 42
Lowest leak - 35
Highest leak - 44
Average large leak - 0.5

Average pressure- 9.1
Average 90% - 8.9

AHI - 34 / 5.4
Apnea - 0 
Hypotonia- 34 / 5.4
Snoring - 6 / 0.9

I’m new so I would  appreciate any input. I’ve been using my APAP for six days now the first two nights my AHI was about 2.3 

THANKS
Post Reply Post Reply
#2
It does produce charts and that will help a lot of you post them.
you need someone to know or you to find out if the leak rate includes the venting air, like philips do. then a leak rate of 40 may be ok. What dies the book say?

For the hypopnea I would raise the min from 8 and go to 9 and see how that goes.
the max I would bring back to 15, It might tighten the algorithm
new http://www.apneaboard.com/wiki/index.php...re_success
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
From machine or charts for auto-cpap, set the min 1cm below median pressure, or 2cm below 90/95%. max at 20cm for now. Forum will help you fine tune settings
Post Reply Post Reply
#3
You can find software for your machine in the Private Files and Links Forum.
OpalRose
Apnea Board Moderator
www.ApneaBoard.com

How to Organize and Post ScreenShots

http://sleep.tnet.com/resources/sleepyhead/shorganize
https://sleep.tnet.com/reference/tips/imgur

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.




Post Reply Post Reply


#4
Use the APEX Easy Compliance software and see where the numbers lead you. The leak rate that the Easy Compliance chart shows is for total leaks, so you will need to subtract the intentional mask leak rate (if there is such a leak chart for the Wizard 220 mask).
lots-o-coffee
The doctor says coffee does not affect my tinnitus and it's got lots of antioxidants.... 
Post Reply Post Reply
#5
Here is a sample of the charts from the Easy Compliance software (under detail tab). Lots of mouth leaks on this one with a Philips Wisp nasal mask.

[Image: k3qXVzn.jpg]
lots-o-coffee
The doctor says coffee does not affect my tinnitus and it's got lots of antioxidants.... 
Post Reply Post Reply
#6
What is everyone getting for a leak rake in L/min for the RESMED AirTouch F20

I have been using a nasal mask and get almost zero leaks. Is there a seal around where the mask joins the headgear I have been looking on line for a picture? Then I got my mask it was already assembled I think they forgot the seal It would have to have some leak rate but this thing i blowing a lot of air and is much nosier than my other mask.
any one have a picture. both mask and headgear are plastic on mine.
Post Reply Post Reply


#7
That is where the mask vents
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Do I have a leak?? Fixit50 6 133 Yesterday, 11:15 PM
Last Post: ajack
  Resmed F20 leak rate tricountytrail 14 351 11-17-2017, 08:08 PM
Last Post: HalfAsleep
  Respironics no leak; Resmed huge leak sc4922 31 678 11-14-2017, 03:53 PM
Last Post: sc4922
  Major Mask Leak Haynbo 3 107 11-14-2017, 01:36 PM
Last Post: jaswilliams
  Resmed Aircurve 10 ASV backup rate tekguymi 11 292 11-07-2017, 12:22 AM
Last Post: trish6hundred
  DIY Amara View Mask Leak Fix jrdnduvall 8 238 11-06-2017, 08:58 PM
Last Post: jrdnduvall
  Unusual low & High Pulse Rate ( Seeking Advise ) BlueJay22 3 141 11-03-2017, 08:34 PM
Last Post: ajack

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.