Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Need help adjusting pressure
#1
SO my VPAP is currently on CPAP but I think I need to increase the pressure. I kept on the last prescribed pressure but I don't think this is right. I did sleep better with the machine than without but do I need to increase the pressure a lot more? I changed the setting back vauto since I will need to have the pressure changed again so ignore the graph that mentioned it is on vpap auto .[Image: vgYsIq8.png]



[Image: Ot8G13D.png]



[Image: hFAKxVs.png]

[Image: T5tR0N8.png]

[Image: RzlI34J.png]
Post Reply Post Reply



Donate to Apnea Board  
#2
You most likley not hit zero. 3.37 is considered good. Anything under 5 is good. Have paitence it takes some time for things to happen.
Post Reply Post Reply
#3
(01-12-2018, 08:50 PM)Gary1of2 Wrote: You most likley not hit zero. 3.37 is considered good. Anything under 5 is good. Have paitence it takes some time for things to happen.

Why does the AHI go up to 10 then and then go back down? Also the flow rate is all over the place too.
Post Reply Post Reply
#4
If your using Ramp I'd turn it off. Also 6cm minimum might feel better.

If you could arrange your charts as shown in the link below it makes it a lot easier to read the charts.

The flow rate didn't look bad but you had a lot of breaks where you turned the machine off during the night.
Post Reply Post Reply
#5
(01-12-2018, 08:53 PM)Sleep Therapy Wrote:
(01-12-2018, 08:50 PM)Gary1of2 Wrote: You most likley not hit zero. 3.37 is considered good. Anything under 5 is good. Have paitence it takes some time for things to happen.

Why does the AHI go up to 10 then and then go back down? Also the flow rate is all over the place too.

The AHI running chart tells you in that period, you would be getting a factor 10.  If it was all night, you would have an ahi of 10. I don't use that chart.
Flow rate is all over the place for a lot of people and is perfectly normal in the stages of sleep.

Did the doctor give you the pressures you are using? I would ask him to review your charts and pressures. I don't think they look right. You could also change your avatar to show you have a vauto bpap
new http://www.apneaboard.com/wiki/index.php...re_success
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
From machine or charts for auto-cpap, set the min 1cm below median pressure, or 2cm below 90/95%. max at 20cm for now. Forum will help you fine tune settings
Post Reply Post Reply



Donate to Apnea Board  
#6
(01-12-2018, 09:48 PM)Walla Walla Wrote: If your using Ramp I'd turn it off. Also 6cm minimum might feel better.

If you could arrange your charts as shown in the link below it makes it a lot easier to read the charts.

The flow rate didn't look bad but you had a lot of breaks where you turned the machine off during the night.

Thanks. I managed to use this thing for about 6.5 hours without taking it off. I dreamt for the first time in months but still felt like my airway had collapsed a few times. The ramp was only at 25 minutes I believe but I am not sure why the AHI went to high as 10 before. 

[Image: 5FOAMIV.png]

[Image: aLG0GmH.png]
Post Reply Post Reply
#7
Your overall numbers aren't bad. The big question is why are you on a VAUTO setup like a CPAP?
Post Reply Post Reply
#8
(01-12-2018, 10:41 PM)Walla Walla Wrote: Your overall numbers aren't bad.  The big question is why are you on a VAUTO setup like a CPAP?

Because I tried APAP and kept taking off the mask.
Post Reply Post Reply
#9
I'd get back to your respiratorist and get the machine set up for you. You're aussie and get access to decent health care, including free at a public hospital. Is it a months trial or what is the story for swapping over.
new http://www.apneaboard.com/wiki/index.php...re_success
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
From machine or charts for auto-cpap, set the min 1cm below median pressure, or 2cm below 90/95%. max at 20cm for now. Forum will help you fine tune settings
Post Reply Post Reply



Donate to Apnea Board  
#10
Sleep Therapy, your events are nearly all central or hypopnea. I'm certain we can find some more comfortable settings using some pressure support (higher inhale pressure, lower exhale pressure), but first I'd like to know more about your diagnostic and any titration study. Do you have copies of your sleep reports? Were central apnea a prominent feature?

If we can setup your Aircurve 10 Vauto it's going to be much more comfortable and easy to breathe, but if you actually have central or complex apnea, then you are possibly on the wrong therapy device.
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Surprised AHI averages in the 40s. Need help adjusting settings. ApneaSufferer 21 384 04-18-2018, 12:30 AM
Last Post: ApneaSufferer
  re-adjusting to ASV Sleeeppp 2 121 04-13-2018, 10:02 PM
Last Post: Sleeeppp
Gross [Pressure] Need immediate help. [adjusting to different machine] Hellodare 72 1,917 04-10-2018, 10:13 PM
Last Post: SarcasticDave94
  Pressure vs Mask Pressure paulag1955 6 487 01-18-2018, 12:30 PM
Last Post: paulag1955
  AHI 7.9 need help adjusting Justbreath 24 739 01-01-2018, 12:26 AM
Last Post: ajack
  [Equipment] Adjusting CPAP Time dracus 6 249 12-05-2017, 10:34 PM
Last Post: Crimson Nape
  Isn't Resmed's Expiratory Pressure Relief really Inspiratory Pressure Support?? Reznik 116 3,769 11-27-2017, 07:28 PM
Last Post: Reznik

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.