Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Need help with date problem with machine/card please.
#1
Need help with date problem with machine/card please.
First off, Happy New Year!

next, my machine thinks it is Jan 1 2016 and I cannot set the date back to 2015 since it says there is data there.

full story: RESMED s9 equipment with SD data card. Machine hadn't been used since Dec 19th since using Oral device while traveling. Back home last night, Dec 31st, and tried to reset time for time zone at home. It would not let me set it for 11pm Dec 31st, 2014 since "data exists for this period". so I tried to set it for 12:05 Jan 1, 2015 and it said data exists for that period as well. so I set it to jan 1 2016 and went to bed and figured I could figure it out today. I can't figure it out and would be grateful for some advice.
- I downloaded and viewed data in both ResScan and SleepyTime. I viewed last nights data as Jan 2016, then deleted the entry off of the card. I didn't see any data around Dec 31st 2014 or Jan 1 2015. But I still cannot get the ResMed machine to accept the current date and time. It still says "data exists for this period".

Thank you in advance
Post Reply Post Reply
#2
RE: Need help with date problem with machine/card please.
Welcome to the forum.

Unplug the power cord for about 3 minutes. Reconnect the power then, prior to inserting the SD card, go into clinician mode and try setting the date and time. Also, re-format the SD card prior to inserting it in the S9.

I hope this helps. Keep us posted.
Crimson Nape
Apnea Board Moderator
www.ApneaBoard.com
___________________________________
Useful Links -or- When All Else Fails:
The Guide to Understanding OSCAR
OSCAR Chart Organization
Attaching Images and Files on Apnea Board
Apnea Helpful Tips

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
RE: Need help with date problem with machine/card please.
Hi Ldempke,
WELCOME! to the forum.!
Hang in there for more responses to your post and much success to you as you continue your CPAP therapy.
trish6hundred
Post Reply Post Reply
#4
RE: Need help with date problem with machine/card please.
(01-01-2015, 12:34 PM)Ldempke Wrote: First off, Happy New Year!

next, my machine thinks it is Jan 1 2016 and I cannot set the date back to 2015 since it says there is data there.

First, you need to erase machine data (configuration menu) before you can set the current date/time

Happy New year to you too Coffee
Post Reply Post Reply
#5
RE: Need help with date problem with machine/card please.
(01-01-2015, 12:54 PM)sgearhart Wrote: Welcome to the forum.

Unplug the power cord for about 3 minutes. Reconnect the power then, prior to inserting the SD card, go into clinician mode and try setting the date and time. Also, re-format the SD card prior to inserting it in the S9.

I hope this helps. Keep us posted.

I did this but ran into the same problem when setting the date and time. Although I didn't re-format the SD card...I was hesitant because I didn't want to lose the data on the SD card before my sleep doctor appt. But then I saw zonk's reply about erasing machine data. That worked. I could then set the date. So if I understand this correctly, the machine data is starting fresh....but the SD card still has the old data on it...and will continue to get the new data so it will be fully loaded with info for the next sleep appt. whew. good night.


(01-01-2015, 05:00 PM)zonk Wrote:
(01-01-2015, 12:34 PM)Ldempke Wrote: First off, Happy New Year!

next, my machine thinks it is Jan 1 2016 and I cannot set the date back to 2015 since it says there is data there.

First, you need to erase machine data (configuration menu) before you can set the current date/time

Happy New year to you too Coffee

yes this worked. Thank you.
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  AirFit F30i Mask Problem OldTeacher 22 4,557 03-23-2024, 03:23 PM
Last Post: ButtonNoseBarbie
  Setting time and date on Resmed Airsense 10 cmadon 42 32,170 03-08-2024, 09:13 AM
Last Post: Sleeprider
  [CPAP] ResMed Air Sense 10 Auto Off Problem Buddie43 19 26,321 03-05-2024, 10:50 PM
Last Post: Ailyhsaun
  Are these flow limits my problem? k888 87 5,456 02-26-2024, 12:02 PM
Last Post: k888
  [Treatment] Are leaks the problem or do I need BIPAP? TiredDude 3 328 02-22-2024, 07:52 PM
Last Post: Sleeprider
  AirTouch F20 mask date code? Labromaniac 4 424 02-14-2024, 12:34 AM
Last Post: Homerec130
  [CPAP] Is my leak rate a problem? Kevstuf 5 549 02-08-2024, 10:25 AM
Last Post: Kevstuf


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.