Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

PMI Probasic Pressure setting
#1
Any information on resetting the pressure on the PMI Probasic Zzzz travel machine? I know it is loud, and no issue there but the pressure is high and out of warranty....
I am thinking of a new traveller, but would like to work with this one first
Post Reply Post Reply
#2
Hi rmeints, welcome to the forum.

I'm not sure if this is the correct machine - Probasics ZZZ-PAP? The instructions are:

Note:
Detailed instruction for "Compliance Meter ™" and the "Therapy Pressure" are separated because of concerns with renting service management and accidental wrong setting by others. Please tear off this page from manual before delivering this product to end-user.

You have been warned Smile

To Set the Prescribed Therapy Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU" button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start blinking to allow you to adjust the therapy pressure from 4 to 18 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting in increments of 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to automatically go back to standby screen 5 seconds later.



DeepBreathing
Apnea Board Moderator
www.ApneaBoard.com


Bed

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
That's perfect! I do appreciate it, hoping in a hotel I may be able to slow the freight train I hear at night when I travel!
Post Reply Post Reply


#4
Hi rmeints,
WELCOME! to the forum.!
Best of luck to you.
trish6hundred
Post Reply Post Reply
#5
Thumbsdown 
Thanks loads, Living on the edge I dropped the setting on this machine 1.5 to 10.5, the noise of course drastically reduced, pressure was fine and I slept crazy good.
Thanks
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  [Equipment] Viscious cycle of increased pressure -> more leak -> response of more pressure 3mp0w3r 5 158 09-16-2017, 09:04 AM
Last Post: OpalRose
  URGENT HELP : ResMed AirCurve 10 VAuto Setting vs. BlueJay22 12 517 08-21-2017, 11:24 PM
Last Post: PaytonA
  Pressure Setting catspurrrr 20 816 08-06-2017, 03:12 PM
Last Post: Rcgop
  [CPAP] trigger setting for ResMed aircurve 10 vauto dwbenziger 5 289 07-25-2017, 04:12 PM
Last Post: Sleeprider
  [Pressure] Help with Pressure Setting Vesimir 7 376 07-20-2017, 09:32 PM
Last Post: DavePaulson
  Mask type setting on Dreamstation? speed3914 1 215 07-13-2017, 08:17 PM
Last Post: Russatrice
  nuance to Swift FX for her setting problems akdog30 12 752 06-24-2017, 12:10 PM
Last Post: jsielke

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.