Hello Guest,
Welcome to Apnea Board !As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address. Login or Create an Account
Pressure setting full face vs pillow
|
01-29-2020, 02:48 PM
Pressure setting full face vs pillow
I have been using a nasal pillow mask since starting therapy. I am having to use a full face due to congestion. Will my starting pressure stay the same?
01-29-2020, 03:03 PM
RE: Pressure setting full face vs pillow
I'd just edit the mask type setting and it should be OK.
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEBSITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
01-29-2020, 03:11 PM
RE: Pressure setting full face vs pillow
I have a dreamstation machine and resumed mask. What does changing mask type setting do?
01-29-2020, 03:57 PM
RE: Pressure setting full face vs pillow
We have found that nasal pillow masks often allow for a lower pressure settings due to the direct application of pressure, and lower volume in the circuit. That said, in your last therapy thread, we have been trying to get you to increase minimum pressure to try to reduce the relatively large number of hypopnea, RERA and flow limitations you experience, so I'll repeat it here...change your minimum pressure to 9.0. Not only are you dealing with a different mask type, equally important is you indicate you are congested. This will increase flow limitation due to airway being impaired. I think this further argues for a higher minimum pressure.
If you are using a Resmed full face mask with the Dreamstation auto, Respironics recommends a resistance of X-0. Unlike the Resmed machines, the Philips uses a resistance factor, not mask type.
Sleeprider
Apnea Board Moderator www.ApneaBoard.com ____________________________________________ Download OSCAR Software Soft Cervical Collar Optimizing Therapy Organize your OSCAR Charts Attaching Files Mask Primer How To Deal With Equipment Supplier INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
01-29-2020, 04:25 PM
RE: Pressure setting full face vs pillow
The setting is different on Resmed and PR machines.
With Resmed machines I believe the mask type is used for calculating leak, tidal volume etc. With the PR machines it is called system one resistance control and I understand that it adjusts the pressure to account for different resistance of masks. I believe they only give recommended settings for their own masks though so if you are using other brands of masks you need to set by feel or can try searching to see what others have it set at. Here are some resistance control settings. https://philipsproductcontent.blob.core....63b068.pdf In short you might need to adjust the mask type setting or your pressures.
01-29-2020, 04:30 PM
RE: Pressure setting full face vs pillow
Thank you. I have changed my pressure and my rera’s dropped to less than 0.6. So, I’ll change to x0, which is off, correct.
01-29-2020, 06:02 PM
(This post was last modified: 01-29-2020, 06:03 PM by ragtopcircus.)
RE: Pressure setting full face vs pillow
The Phillips Respironics recommendation of X0 for non-PR masks is utter CYA nonsense unless you stick the end of the hose directly in your mouth. I would never use less than X1 for ANY mask.
01-29-2020, 06:33 PM
(This post was last modified: 01-30-2020, 12:44 PM by ragtopcircus.)
RE: Pressure setting full face vs pillow
X1 is what I found most comfortable with an F20 or F30. It’s a reasonable default for most masks. A few may require X2. None are likely to need a higher setting unless you use an antibacterial filter or HME.
For example, if I use the F20 or F30 with an inline Heat Moisture Exchanger instead of the humidifier (during a power failure), I bump it up from X1 to X3 to compensate for the extra restriction. PR recommends X1 for the Dreamwear, but I suspect some side-sleepers might be more comfortable at X2 (for any of the Dreamwear versions) to compensate for partially pinching one tube. Some pillow masks may also need X2, especially for a small size cushion due to the smaller holes.
01-29-2020, 06:53 PM
RE: Pressure setting full face vs pillow
Just to make sure I understand, X1 is more flow than X2 and so on.
01-29-2020, 07:01 PM
(This post was last modified: 01-30-2020, 12:32 PM by ragtopcircus.)
RE: Pressure setting full face vs pillow
[deleted redundant content]
|
« Next Oldest | Next Newest »
|
Possibly Related Threads... | |||||
Thread | Author | Replies | Views | Last Post | |
Diagnosed with UARS just got CPAP with mask need help setting it up | nicchamilton | 2 | 78 |
Yesterday, 03:26 PM Last Post: HalfAsleep |
|
[Equipment] Mask recommendation for a sensitive side-sleeper who might have an unusual face shape | PersonInNY | 6 | 196 |
Yesterday, 10:44 AM Last Post: PersonInNY |
|
N30i [what mask setting] Airsense 10 AutoSet | Topdogg7505 | 8 | 3,242 |
04-20-2024, 10:02 AM Last Post: ahfairley |
|
[Equipment] Any tips on how to get better airflow in under nose masks/hybrid full face masks? | jake79 | 16 | 343 |
04-19-2024, 10:58 AM Last Post: jake79 |
|
[CPAP] Congested/painful itch reaction/face hotness upon use of CPAP | Yeliad | 6 | 183 |
04-15-2024, 10:44 PM Last Post: Yeliad |
|
Resmed Airsense 10 time to return to low pressure setting | jfchap | 3 | 176 |
04-13-2024, 03:54 PM Last Post: SarcasticDave94 |
|
Adjusting to Nasal Pillow Mask | DenKen31 | 9 | 1,021 |
04-12-2024, 09:57 PM Last Post: MaskedOne |