Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

ResMed AirSense 10 Auto - Unable to turn off Ramp
#11
Thanks AlanE for your detailed help! I have the ramp turned off now Smile
Post Reply Post Reply
#12
You're welcome sir.


Using FlashAir W-03 SD card in machine. Access through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie

Post Reply Post Reply
#13
(08-06-2015, 07:51 AM)AlanE Wrote:
(08-05-2015, 07:48 AM)Dagmar Wrote: I cannot figure out how to turn off the ramp setting. I am in the Clinical menu, but Ramp is greyed out as an option. It is set to Auto with a starting pressure of 5. But, I really don't want it on or I would like it set higher. I can not seem to change the Ramp setting from either the patient or clinical menu. Can anyone help with this?

In the clinician's menu check under Therapy if your mode is set to anything other than Autoset.

Take your machine off of "auto" and the grey will be gone.
Post Reply Post Reply


#14
You had an idea you needed to increase your pressure, or at least thought it was a good idea. You had settings of 6 - 12 on Aug 4. Although nearly all of your events were CA, and are not treated with pressure, your machine did increase pressure during other parts of the night. It did so because it sensed obstruction, partial obstruction, or resistance to flow. So, raising minimum pressure may make sense.

If these were my readings, I would note that my pressure never was below 7 except at startup, and my pressure was above 8.6 at least half of the time. I would gradually change my minimum pressure until it was within 2 cmH2O of my 90% pressure (9.2). I would increase minimum pressure to 7 and then monitor for 4 to 5 days before stepping up again, by .5 cmH2O every 4 to 5 days until 9.2 is achieved.

I would be monitoring for reduction of machine reaction (pressure swings), and to ensure I was not picking up significantly more CA readings.

[I would also reduce the EPR setting from 3 to 2 as this sometimes reduces the number of CA events, although CA events generally go away or are reduced on their own.]

QAL
Dedicated to QALity sleep.
You'll note I am listed as an Advisory Member. I am honored to be listed as such. See the fine print - Advisory Members as a group provide advice and suggestions to Apnea Board administrators and staff concerning Apnea Board operation and administrative policies. Membership in the Advisory Member group should not be understood as in any way implying medical expertise or qualification for advising Sleep Apnea patients concerning their treatment.
Post Reply Post Reply
#15
(08-06-2015, 07:51 AM)AlanE Wrote:
(08-05-2015, 07:48 AM)Dagmar Wrote: I cannot figure out how to turn off the ramp setting. I am in the Clinical menu, but Ramp is greyed out as an option. It is set to Auto with a starting pressure of 5. But, I really don't want it on or I would like it set higher. I can not seem to change the Ramp setting from either the patient or clinical menu. Can anyone help with this?

In the clinician's menu check under Therapy if your mode is set to anything other than Autoset.

Turning off the ramp is easy.
Go into "clinical Menu" (hold the Home button and the selector knob in for 8 or 10 seconds)
Click on "Auto Ramp Time" ( You need to turn off "Auto" before it will allow you to adjust the time)
Now the time setting is no longer greyed out.
Turn the wheel to your desired setting. "OFF" is at the end of the circular graph.
Click wheel to save.
Your done, Sleep-well

Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  SoClean 2 for Resmed AirSense 10 Auto Orionsnet 14 208 1 hour ago
Last Post: bonjour
  Respironics Everflo Q-Settings when connected to ClimateLine Oxy for AirSense 10 Auto Orionsnet 3 60 Today, 09:01 AM
Last Post: justMongo
  [CPAP] Resmed Airsense 10 Autoset - Need advanced help... Kayak18 10 184 Yesterday, 07:01 PM
Last Post: Sleeprider
  [Pressure] New AirSense 10 Auto User-Need Help w/initial Pressure Min/Max Settings Orionsnet 48 1,084 Yesterday, 04:58 PM
Last Post: Orionsnet
  Problems with AirFit P10 Nasal Pillows (+ResMed AirSense 10) numari 18 6,997 03-23-2017, 11:36 AM
Last Post: PaytonA
  [CPAP] ResMed Air Sense 10 Auto Off Problem Buddie43 18 4,792 03-21-2017, 03:23 PM
Last Post: CPAPPY262
  Resmed Airsense "response" soft or standard Binti1962 9 281 03-21-2017, 01:22 PM
Last Post: Attila

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.