Thread Closed 
ResScan CPAP Reporting Software (current version: 5.5) [Archived Discussions]
Author Message
retired_guy Offline

Preferred Members-2

Posts: 2,744
Joined: Jan 2014

Machine: ResMed S9 Autoset
Mask Type: Nasal pillows
Mask Make & Model: Resmed Airfit P10
Humidifier: ResMed
CPAP Pressure: 10.6/14, EPR 3
CPAP Software: ResScan SleepyHead

Other Comments: Is it bedtime yet?

Sex: Male
Location: Beautiful, albeit very wet Oregon Coast

Post: #701
RE: ResScan CPAP Reporting Software (current version: 5.1)
(08-19-2014 04:36 PM)jcarerra Wrote:  Can 5.1 be installed "on top of" 4.5?

If we do that, will 5.1 autmatically "see" the data saved running 4.5?

Yes.

and

Yes.
08-19-2014 04:40 PM
Find all posts by this user

Donate to Apnea Board
PaytonA Offline
Wiki Editor
Monitors

Posts: 3,005
Joined: Dec 2013

Machine: ResMed S9 VPAP Auto
Mask Type: Full face mask
Mask Make & Model: Resmed Mirage Quattro
Humidifier: H5i(distilled-top up)
CPAP Pressure: VAuto MinE14.0 MaxI 20.6 PS4.0
CPAP Software: ResScan SleepyHead

Other Comments:

Sex: Male
Location: Orange County,California

Post: #702
RE: ResScan CPAP Reporting Software (current version: 5.1)
Is the location of the zip file for 5.1 critical when you unzip it. Does one need to identify a specific zip target file or is there an installer inside the zip file?
08-20-2014 12:28 PM
Find all posts by this user
jcarerra Offline

Advisory Members

Posts: 284
Joined: Jun 2014

Machine: ResMed S9 Adapt SV
Mask Type: Full face mask
Mask Make & Model: Quattro
Humidifier: H5i
CPAP Pressure: min/max EPAP 9/15 min/max PS 4
CPAP Software: ResScan

Other Comments:

Sex: Male
Location: Florida

Post: #703
RE: ResScan CPAP Reporting Software (current version: 5.1)
(08-20-2014 12:28 PM)PaytonA Wrote:  Is the location of the zip file for 5.1 critical when you unzip it. Does one need to identify a specific zip target file or is there an installer inside the zip file?

Just did it. Yes, there is an installer inside the zip. You need to unzip it anywhere, find the setup.exe file and run that. Remember to NOT SELECT the drivers for install if you already have a working SD card reader.
08-20-2014 12:32 PM
Find all posts by this user

Donate to Apnea Board
Chiphines Offline

New Members

Posts: 1
Joined: Nov 2012

Machine: ResMed S9
Mask Type: Full face mask
Mask Make & Model: Unsure
Humidifier: Resmed s9
CPAP Pressure: 13
CPAP Software: Not using software

Other Comments:

Sex: Male
Location: Satellite Beach, FL

Post: #704
RE: ResScan CPAP Reporting Software (current version: 5.1)
I just tried running the ResScan installation software and it failed with a message "Key not valid for use in specified state." I had selected complete install (the default) and did not check any of the three boxes.

this was version 5.1.xxxx

any ideas? Im on a win 8.1 64 bit machine.
08-21-2014 02:34 PM
Find all posts by this user
Sleepster Offline
Wiki Editor
Moderators

Posts: 4,988
Joined: Feb 2012

Machine: ResMed AirCurve10 VAuto
Mask Type: Full face mask
Mask Make & Model: F&P Simplus
Humidifier: HumidAir and SlimLine Hose
CPAP Pressure: MaxI 13.6 | MinE 5.2 | PS 4.4
CPAP Software: ResScan SleepyHead

Other Comments: Diagnosed Nov 2011. Conquered aerophagia.

Sex: Male
Location: Houston, Texas

Post: #705
RE: ResScan CPAP Reporting Software (current version: 5.1)
(08-21-2014 02:34 PM)Chiphines Wrote:  I just tried running the ResScan installation software and it failed with a message "Key not valid for use in specified state."

Try right-clicking on the file and then select "run as administrator".

Sleepster
Apnea Board Moderator
www.ApneaBoard.com


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
08-23-2014 04:29 PM
Find all posts by this user

Donate to Apnea Board
Kenmac1005 Offline

Members

Posts: 5
Joined: Sep 2012

Machine: Resmed S8 25
Mask Type: Nasal mask
Mask Make & Model: Respironics
Humidifier: S8
CPAP Pressure: 5.1
CPAP Software: ResScan

Other Comments:

Sex: Male
Location: NYC

Post: #706
RE: ResScan CPAP Reporting Software (current version: 5.1)
Loaded the 5.1 version on my HP Elitepad and my laptop. both work fine with my S8 VPAP Auto 25 old S8 datacard which is a real surprise as it was very iffy with the old version.
08-29-2014 08:35 AM
Find all posts by this user
Topster10 Offline

New Members

Posts: 1
Joined: Dec 2013

Machine: Quattro
Mask Type: Full face mask
Mask Make & Model: unsure
Humidifier: unsure
CPAP Pressure: 2-14
CPAP Software: ResScan

Other Comments:

Sex: Male
Location:

Post: #707
ResScan Software
Have been using Res Scan software for a while, but it now will not start and says tit is looking for a communications device library. Cannot find my original installation file. Any way I can find file it is missing and where it belongs? Sent email as per instructions on this forum foe obtaining Res Scan software, no answer at all.
Any help would be great.
09-06-2014 09:08 PM
Find all posts by this user

Donate to Apnea Board
trish6hundred Offline

Advisory Members

Posts: 6,430
Joined: May 2012

Machine: Resmed S9 AutoSet for Her
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: H5i Heated Humidifier
CPAP Pressure: 10 - 7-20 Cm H2O
CPAP Software: Not using software

Other Comments: I started CPAP in 2008. Totally blind since birth.

Sex: Female
Location: Missouri, USA

Post: #708
RE: ResScan Software
Hi Topster10,
WELCOME! to the forum.!
I don't use the ResScan software but there are plenty of people here who do, so hang in there, someone will be along soon to help.
Best of luck to you as you continue CPAP therapy.

trish6hundred
09-06-2014 09:20 PM
Find all posts by this user
Sleepster Offline
Wiki Editor
Moderators

Posts: 4,988
Joined: Feb 2012

Machine: ResMed AirCurve10 VAuto
Mask Type: Full face mask
Mask Make & Model: F&P Simplus
Humidifier: HumidAir and SlimLine Hose
CPAP Pressure: MaxI 13.6 | MinE 5.2 | PS 4.4
CPAP Software: ResScan SleepyHead

Other Comments: Diagnosed Nov 2011. Conquered aerophagia.

Sex: Male
Location: Houston, Texas

Post: #709
RE: ResScan Software
NOTE: If you do not receive an email response within 10 minutes, try sending your request from a different email account.

Sleepster
Apnea Board Moderator
www.ApneaBoard.com


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
09-06-2014 09:30 PM
Find all posts by this user

Donate to Apnea Board
GeoffD Offline

Preferred Members-2

Posts: 194
Joined: Sep 2014

Machine: ResMed Airsense 10 AutoSet
Mask Type: Nasal pillows
Mask Make & Model: ResMed AirFit P10
Humidifier: Integral + ClimateLine
CPAP Pressure: 14-17
CPAP Software: ResScan

Other Comments:

Sex: Male
Location: New England

Post: #710
RE: ResScan CPAP Reporting Software (current version: 5.1)
My only problem was the email from the gmail account with the link to the software was trapped by the spam filters for both my work and personal email servers. I tried to email a 3rd time from a disused gmail account I have and that worked fine. On 64-bit Win7 Pro, the software installed and the application works just fine. My laptop has an SD flash card slot and that worked perfectly. ResMed S9 Autoset. One night now under my belt and I can now access the data to see how I'm doing.
09-10-2014 01:24 PM
Find all posts by this user
Thread Closed 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Arrow [Admin Note] ResScan - [version 5.7] SuperSleeper 57 6,932 12-01-2016 12:43 PM
Last Post: SuperSleeper
  ResScan 5.5 cannot run in Windows 10 ant08 6 306 12-01-2016 12:21 PM
Last Post: cbramsey
  ResScan - not supported jmitchell151 2 124 11-23-2016 11:23 PM
Last Post: SuperSleeper
  new ResMed machine and ResScan software issue fluffyetal 1 181 11-18-2016 06:40 AM
Last Post: Sleeprider
  can resscan read cards from two machines whirschb 8 477 11-14-2016 04:03 PM
Last Post: Mosquitobait
Question ResScan=Unable to detect device communications library cobaltpanther 6 590 11-12-2016 02:19 PM
Last Post: Kitalarium
  ResScan Prometheus 4 351 11-04-2016 07:11 PM
Last Post: SuperSleeper

Forum Jump:

Who's Online (Complete List)