Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Resmed 9 autoset problem
#1
Question 
Resmed 9 autoset problem
Hi All,

My brother lives in a far province in Russia. He has been using his CPAP for 2 years and it worked fine. But recently it started behaving weirdly despite the fact that no changes has been done to any settings whatsoever.

A cycle starts OK but then the machine rises the pressure and keeps it high though breathing stays the same. He performed 'mask test' and it ran OK, so no leaks, I assume.

I wonder if there is any way to do a factory reset of the machine or any diagnostic procedure? Service is not available at that area, so a tip or advice are highly appreciated!

TIA,
Philipp
Post Reply Post Reply
#2
RE: Resmed 9 autoset problem
You can download the clinician's manual here. You can reset the machine.

http://www.apneaboard.com/forums/Thread-...13#pid8013
Sleepster

INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
RE: Resmed 9 autoset problem
Thank you for the prompt reply. I followed the link you provided but was able to find only Clinical Setup and Change pressure guides. Did I look through the section with the machine reset?

Post Reply Post Reply
#4
RE: Resmed 9 autoset problem
Here the S9 instruction video and how to get the clinical manual for your CPAP machine
http://www.apneaboard.com/resmed-s9-cpap-setup

Welcome
Post Reply Post Reply
#5
RE: Resmed 9 autoset problem
If this is a S9 autoset and the machine increases pressure for no cause, it could be put into CPAP mode. This should continue to provide therapeutic pressure without changes in pressure. Not an ideal solution, but it should help until the machine can be replaced or a better fix is available.
Sleeprider
Apnea Board Moderator
www.ApneaBoard.com

____________________________________________
Download OSCAR Software
Soft Cervical Collar
Optimizing Therapy
Organize your OSCAR Charts
Attaching Files
Mask Primer
How To Deal With Equipment Supplier


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#6
RE: Resmed 9 autoset problem
Hi phi1ipp,
WELCOME! to the forum.!
Much success to you with helping your brother with his machine.
Hang in there for more responses to your post.
trish6hundred
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
Question New CPAP User - Help Please - ResMed Airsense 11 Autoset Pawpri 25 465 1 hour ago
Last Post: Old Steve
  Need help with Airsense 10 AutoSet JonUK 2 118 03-25-2024, 06:11 PM
Last Post: JonUK
  AirFit F30i Mask Problem OldTeacher 22 4,578 03-23-2024, 03:23 PM
Last Post: ButtonNoseBarbie
  ResMed S9 AutoSet and OSCAR - Help Appreciated Slippy 12 477 03-16-2024, 08:56 AM
Last Post: Slippy
  [CPAP] ResMed Air Sense 10 Auto Off Problem Buddie43 19 26,335 03-05-2024, 10:50 PM
Last Post: Ailyhsaun
  ResMed Airsense 10 AutoSet and Oscar Bucktilley 4 216 03-05-2024, 04:41 PM
Last Post: Bucktilley
  Are these flow limits my problem? k888 87 5,475 02-26-2024, 12:02 PM
Last Post: k888


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.