Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Resmed A10 Climate Hose Not Holding Mask Hose
#1
My A10 hose rubber end fitting seems to have stretched and now the mask hose pops out on it's own. Anyone experience this? Is there a DIY fix?

Thanks
Post Reply Post Reply
#2
No fix.

Get a new hose and be more careful next time not to stretch it.
Post Reply Post Reply
#3
You can use electricians tape on the mask to increase diameter and it will hold. A good rubber band or zip-tie may also keep it secured. This has been reported fairly frequently. Ultimately you will need a new hose, but these fixes will work. Try to avoid disconnecting so often, or at least don't stretch the connection end by pulling at an angle rather than straight off.
Post Reply Post Reply


#4
Hi player,
psychomike has a thread here on this board called ""ClimateLine" issues."
He has a solution that will help you.
Good luck with your temporary fix, 'till you are able to get a new hose.
trish6hundred
Post Reply Post Reply
#5
The zip tie works well. My Climateline was held on by a zip tie all last winter. The only thing that I did not do was to knock down the sharp edges with an emery board which is a good idea. Frankly, I view this as more than a temporary fix. This may be a baling wire and chewing gum fix but I see no need to throw away a hose that is perfectly good in all other ways. I have gotten a second Climateline hose as a back-up just in case.

Best Regards,

PaytonA

Admin Note:
PaytonA passed away in September 2017
Click HERE to read his Memorial Thread

~ Rest in Peace ~
Post Reply Post Reply
#6
The mistake I made was fitting it (stretching it) onto my kitchen sink tap and running super hot water through the hose.
Post Reply Post Reply


#7
OOPS!!!

Admin Note:
PaytonA passed away in September 2017
Click HERE to read his Memorial Thread

~ Rest in Peace ~
Post Reply Post Reply
#8
(10-09-2016, 11:27 PM)player Wrote: The mistake I made was fitting it (stretching it) onto my kitchen sink tap and running super hot water through the hose.

Hmmm, I don't recall seeing that method in the cleaning instructions. This is self-inflicted, but using a zip-tie, pipe clamp or similar should still work.
Post Reply Post Reply
#9
Well, how old is the hose? These are supposed to be replaced every 3 months if memory serves me. If it is worn it is time for a new hose for sure. I have two of the climate hoses and neither of them do this. I don't use them anymore due to sanitation issues. They are tough to clean properly and I don't need to be breathing in mold or mildew spores, that defeats the purpose of the thing. So for the sake of ones health replace it. The hose is telling you it is time. Now, if the hose is only a week old then that is an issue. Then I might blame the mask interface.
Post Reply Post Reply


#10
The hose is a year old. When you buy this stuff out of pocket it is tough to throw away a good hose...
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  [Equipment] Heated hose setting ruiparede 7 240 12-08-2017, 02:06 AM
Last Post: Ghost1958
  [CPAP] Full Mask ResMed F10 Not Working sammiller 3 179 11-30-2017, 03:34 PM
Last Post: sammiller
  ResMed "for Her" full mask differences? jaw2004 8 296 11-11-2017, 02:47 PM
Last Post: jaw2004
  ResMed F20 mask magnets & pacemakers WLKSRQ 19 2,811 11-10-2017, 11:07 PM
Last Post: srlevine1
  Air Mini Hose noise solution Frequenttraveler 18 2,322 11-07-2017, 11:57 PM
Last Post: donmeek
  12mm hose on Dreamstation ghstudio 5 315 11-07-2017, 12:11 AM
Last Post: David Govan
  Water in Hose shinkdavid 4 310 10-25-2017, 10:03 AM
Last Post: sonicboom

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.