Post Reply 
Resmed Aircurve 10 ASV Start/Stop Button
Author Message
marose1 Offline

Members

Posts: 11
Joined: Jan 2016

Machine: Resmed Aircurve 10 ASV
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: Integral
CPAP Pressure: EPAP 10 to 10 PS 0 to 15
CPAP Software: ResScan SleepyHead

Other Comments: Former PR BiPaP @ EPAP 15 IPAP 20

Sex: Male
Location: Las Vegas

Post: #1
Resmed Aircurve 10 ASV Start/Stop Button
From Aircurve User Manual: "When SmartStart is enabled, therapy starts automatically when you breathe into your mask. When you remove your mask, it stops automatically after few seconds."

My Actual experience with Smartstart turned ON and mask setting is FULL FACE:

Device is operating normally - Remove mask - Device blower sounds loud for a few seconds and then device blower sounds very softly for 30 minutes and then device blower shuts OFF (device remains turned ON).

Device is operating normally - Push Stop/Start button briefly and then immediately remove mask - Device blower sounds very softly for 30 minutes and then device blower shuts OFF (device remains turned ON).

Device is operating normally - Push Start/Stop Button for several seconds – Device shuts OFF.

Device is shut OFF – Mask is removed – Push Start/Stop Button briefly – Device Turns ON & blower remains OFF.

Device is shut OFF - Breathe into mask - Device remains shut OFF

Device is turned ON - Breathe into mask - Therapy starts automatically

Based on the preceding, when I want to shut OFF my device, I press the Start/Stop Button for several seconds. When I want my device turned but in standby mode (My Air transmissions, etc.), I first make sure the device is turned OFF and then I press the Start/Stop Button briefly to put the device in standby mode.
03-26-2016 12:15 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
vsheline Offline

Advisory Members

Posts: 1,935
Joined: Jul 2012

Machine: S9 VPAP Adapt (USA Model# 36007, not better 36037 or 36067)
Mask Type: Full face mask
Mask Make & Model: F10 or SimPlus w/ 2Liners. MirageQuatro & Gecko gel pad
Humidifier: H5i
CPAP Pressure: 15 EPAP, PS 5-10
CPAP Software: ResScan

Other Comments: Marfan Syndrome, chronic bradycardia, occasional Cheyne-Stokes Respiration

Sex: Male
Location: California, USA

Post: #2
RE: Resmed Aircurve 10 ASV Start/Stop Button
(03-26-2016 12:15 PM)marose1 Wrote:  From Aircurve User Manual: "When SmartStart is enabled, therapy starts automatically when you breathe into your mask. When you remove your mask, it stops automatically after few seconds."

My Actual experience with Smartstart turned ON and mask setting is FULL FACE:

Device is operating normally - Remove mask - Device blower sounds loud for a few seconds and then device blower sounds very softly for 30 minutes and then device blower shuts OFF (device remains turned ON).

Device is operating normally - Push Stop/Start button briefly and then immediately remove mask - Device blower sounds very softly for 30 minutes and then device blower shuts OFF (device remains turned ON).

Device is operating normally - Push Start/Stop Button for several seconds – Device shuts OFF.

Device is shut OFF – Mask is removed – Push Start/Stop Button briefly – Device Turns ON & blower remains OFF.

Device is shut OFF - Breathe into mask - Device remains shut OFF

Device is turned ON - Breathe into mask - Therapy starts automatically

Based on the preceding, when I want to shut OFF my device, I press the Start/Stop Button for several seconds. When I want my device turned but in standby mode (My Air transmissions, etc.), I first make sure the device is turned OFF and then I press the Start/Stop Button briefly to put the device in standby mode.

The cool down feature (20 minutes, I think) is important to reduce moisture in the machine and the hose.

Also, I am too busy to wash my tube every week, so, instead, I merely drain the water tub every morning and turn on the pre-heat mode. This runs the blower on a very low speed for 20 minutes warm-up plus 20 minutes cool-down, totally removing moisture, so nothing nasty grows in the machine or hose.

The airflow is very, very low compared to normal operation, so wear and tear on the blower and filter is negligible.

Membership in the Advisory Member group should not be understood as in any way implying medical expertise or qualification for advising Sleep Apnea patients concerning their treatment. The Advisory Member group provides advice and suggestions to Apnea Board administrators and staff on matters concerning Apnea Board operation and administrative policies - not on matters concerning treatment for Sleep Apnea. I think it is now too late to change the name of the group but I think Voting Member group would perhaps have been a more descriptive name for the group.
(This post was last modified: 03-26-2016 05:56 PM by vsheline.)
03-26-2016 05:52 PM
Find all posts by this user Post Reply Quote this message in a reply
palerider Offline

Preferred Members-

Posts: 440
Joined: Nov 2014

Machine: s9 vpap auto
Mask Type: Nasal pillows
Mask Make & Model: p10
Humidifier: none
CPAP Pressure: 18/13+
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Dallas(ish)

Post: #3
RE: Resmed Aircurve 10 ASV Start/Stop Button
is there a question in there somewhere?

smartstart is doing what it's supposed to do, going from standby to operation mode when you start, or stop breathing.

you'll notice there's a flashing snowflake when it's in cooldown mode (that 30 minutes you're talking about)
03-26-2016 06:01 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
marose1 Offline

Members

Posts: 11
Joined: Jan 2016

Machine: Resmed Aircurve 10 ASV
Mask Type: Full face mask
Mask Make & Model: Fisher & Paykel Simplus
Humidifier: Integral
CPAP Pressure: EPAP 10 to 10 PS 0 to 15
CPAP Software: ResScan SleepyHead

Other Comments: Former PR BiPaP @ EPAP 15 IPAP 20

Sex: Male
Location: Las Vegas

Post: #4
RE: Resmed Aircurve 10 ASV Start/Stop Button
(03-26-2016 06:01 PM)palerider Wrote:  is there a question in there somewhere? (Kevin Bacon-A Few Good Men)

smartstart is doing what it's supposed to do, going from standby to operation mode when you start, or stop breathing.

you'll notice there's a flashing snowflake when it's in cooldown mode (that 30 minutes you're talking about)

Thanks PaleRider - I just got the machine 4 days ago and I learn new things every day. You just explained the 30 minute mystery to me.
03-26-2016 11:36 PM
Find all posts by this user Post Reply Quote this message in a reply
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Why does my pressure start increasing when I'm awake? Ihaveapnea 11 260 Yesterday 11:17 PM
Last Post: Beej
  [Equipment] Auto start on resmed elite s9 justka 5 169 01-08-2017 07:42 PM
Last Post: zonk
Surprised [Treatment] How do I stop periodic breathing??? Rcgop 16 573 01-08-2017 05:59 PM
Last Post: Rcgop
  Now THIS is the way to start the new year! AHI of Zero, Zip, Nada last night! geekbearinggifts 4 211 01-03-2017 06:23 AM
Last Post: pupcamper
  Resmed Aircurve V10 Auto data? Dshow 6 242 01-02-2017 06:10 PM
Last Post: trish6hundred
  When do the morning headaches stop? cate1898 14 1,932 12-23-2016 04:16 PM
Last Post: Sleeping Beauty
  [Pressure] Change Pressure on AirCurve 10 VAuto info 32 5,716 12-20-2016 12:26 AM
Last Post: _cy_

Forum Jump:

Who's Online (Complete List)