Post Reply 
SleepyHead ... Issue with the 2 graph views
Author Message
Stevie1under Offline

Members

Posts: 5
Joined: Sep 2016

Machine: Resmed Air Sense 10
Mask Type: Nasal mask
Mask Make & Model: Respironics Dreamwear
Humidifier: Yes
CPAP Pressure: 9
CPAP Software: SleepyHead

Other Comments: Using SleepyHead, Flashair SD card, and FlashPAP = 1 click to load data, SD card stays put.

Sex: Male
Location: Penticton, BC, Canada

Post: #1
SleepyHead ... Issue with the 2 graph views
Howdy folks,

When I start SleepyHead the first graph view I select, either daily or overview works fine, but when I switch to the other view, that set of graphs doesn't show properly, nor respond to mouse overs. Anyone else experience this? And/or know of a resolution?

Thanks kindly,
Steve
10-15-2016 07:04 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Ockrocket Offline

Advisory Members

Posts: 164
Joined: Jul 2016

Machine: Philips Dreamstation.
Mask Type: Nasal mask
Mask Make & Model: F&P Eson.
Humidifier: Philips Dreamstation.
CPAP Pressure: 7.0
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Windsor (near enough) NSW, Au.

Post: #2
RE: SleepyHead ... Issue with the 2 graph views
Welcome to the group Stevie..

The Sleepyhead issue must have something to do with us who are named 'Steve' Dielaughing

I had/have the same problem at times.

To overcome it I found that altering the internal data box sizes within the window would allow the page to be scrolled up/down again.

Another problem that can happen in Sleepyhead is if you go to a maximized window you may find you don't have the Close, Restore Down and Minimize buttons showing in the top right corner of the window.
To close the Sleepyhead program you can use the key combination of Alt F4.

Ctrl Alt Del is another option for closing the program, in Windows 10 you will be given a choice of what you want to do with the program/s..
With older versions of Windows the Ctrl Alt Del will fully shut down and restart the computer, it was referred to as a "warm boot" for us older computer users. oldman

Let us know how you go with it all.

Cheers,
Ock. [aka Stephen or Steve Laugh-a-lot ]
10-15-2016 07:22 PM
Find all posts by this user Post Reply Quote this message in a reply
Stevie1under Offline

Members

Posts: 5
Joined: Sep 2016

Machine: Resmed Air Sense 10
Mask Type: Nasal mask
Mask Make & Model: Respironics Dreamwear
Humidifier: Yes
CPAP Pressure: 9
CPAP Software: SleepyHead

Other Comments: Using SleepyHead, Flashair SD card, and FlashPAP = 1 click to load data, SD card stays put.

Sex: Male
Location: Penticton, BC, Canada

Post: #3
RE: SleepyHead ... Issue with the 2 graph views
Thanks Steve, that was helpful. I wasn't sure what an internal data box was, but was curious about the full screen stuff. I switched to full screen, ... and voila! ... both graph views worked properly as I switched back and forth and forth and back quite a few times. And they continued to work properly when I switched out of full screen.

On another note, I notice you use a BIPAP machine. Would you care to have your brain picked a little and if so, in a forum for public consumption or via PM?

Thanks again!
(This post was last modified: 10-15-2016 08:26 PM by Stevie1under.)
10-15-2016 08:22 PM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Ockrocket Offline

Advisory Members

Posts: 164
Joined: Jul 2016

Machine: Philips Dreamstation.
Mask Type: Nasal mask
Mask Make & Model: F&P Eson.
Humidifier: Philips Dreamstation.
CPAP Pressure: 7.0
CPAP Software: SleepyHead

Other Comments:

Sex: Male
Location: Windsor (near enough) NSW, Au.

Post: #4
RE: SleepyHead ... Issue with the 2 graph views
Good that it worked for you, on one of my laptops the buttons for switching back out of full screen disappear, and on the small view the scroll down options didn't work, which is how I know about resizing the box within the main window.

And my brain contains very little information, useless or otherwise.... but ask away.

You will find plenty of more knowledgeable people will chime in with answers as well if you ask in the open. [unless you have specific queries you want to keep private, then PM is ok]
10-16-2016 06:08 AM
Find all posts by this user Post Reply Quote this message in a reply
AlanE Offline

Advisory Members

Posts: 1,491
Joined: Mar 2015

Machine: ResMed AirSense 10 Autoset
Mask Type: Nasal pillows
Mask Make & Model: P10 & Mirage Liberty backup
Humidifier: Built-in
CPAP Pressure: 10-14
CPAP Software: ResScan SleepyHead

Other Comments: ʕ•ᴥ•ʔ So Long, and Thanks for All the Fish

Sex: Male
Location: Southwest Florida

Post: #5
RE: SleepyHead ... Issue with the 2 graph views
Press F11 key twice.



Using FlashAir W-03 SD card in machine. Access through wifi with FlashPAP or Sleep Master utilities.

I wanted to learn Binary so I enrolled in Binary 101. I seemed to have missed the first four courses. Big Grinnie
10-16-2016 09:16 AM
Find all posts by this user Post Reply Quote this message in a reply

Donate to Apnea Board
Post Reply 


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  ENCOREBASIC ISSUE AVIGO 0 107 11-19-2016 12:06 PM
Last Post: AVIGO
  SleepyHead Export to CSV Issue bluetooth 1 122 11-18-2016 03:05 PM
Last Post: pholynyk
  new ResMed machine and ResScan software issue fluffyetal 1 176 11-18-2016 06:40 AM
Last Post: Sleeprider
  SleepyHead FRUSTRATION! [graph turns black] mcsheltie 56 1,061 11-01-2016 07:09 PM
Last Post: Sleeprider
  RDI graph wont display sleepyhead beta2 car54 2 209 09-09-2016 05:37 PM
Last Post: car54
  CMS-50F graph not matching SPo2 assistant 2.8 Marthajoy7 0 167 08-12-2016 11:04 PM
Last Post: Marthajoy7
Question Gray bars in sleepyhead overview USAGE graph qualtech 2 320 07-11-2016 09:18 PM
Last Post: qualtech

Forum Jump:

Who's Online (Complete List)