Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

System One resistance setting for a F/P Opus 360 nasal pillow?
#1
Can not find a resistance setting for an Opus nasal pillow for Respironics System One Auto. Help!
Post Reply Post Reply
#2
(06-06-2013, 09:53 PM)MZig Wrote: Can not find a resistance setting for an Opus nasal pillow for Respironics System One Auto. Help!
Unlike ResMed mask selection to do with leak rate calculation, not sure what system one resistance suppose to do. Just another way to use their own masks. anyway from what read, system one resistance for non,-Respironcis masks is "0"
[Image: MaskSettingsforSystemOneResistanceC.jpg]

Post Reply Post Reply
#3
Hi MZig,
WELCOME! to the forum.!
Hang in there for more suggestions and best of luck to you.
trish6hundred
Post Reply Post Reply


#4
If you perform a Google search on "systemoneresistancecontrol" (all one word with no spaces) and look for the entry at respironics.com, you will see graphs that describe the SystemOne Resistance Control.

The graphs on the left are the pressure as measured at the CPAP machine. The graphs on the right are the pressure as measured in your airway. The graphs on the top are without resistance compensation, and the graphs on the bottom are with resistance compensation.

Basically, the machine intentionally under-/over-compensates the provided pressure to make sure that the final delivered pressure corresponds to the intended pressure profile.

For obvious reasons, Philips does not provide compensation values for non-Respironics masks, rather specifying that the resistance control setting be turned off. You could probably (maybe) find a comparable Respironics mask to your Opus nasal pillow and try that setting.
Post Reply Post Reply
#5
Zonk is correct. Non-Respironics masks do not have a specified "System One Resistance" setting. Sleep-well
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#6
Guess I got lucky when I bought the comfort gel full face mask ...it has a resistance number for my S1...so sad how manufacturers sneak this crapware into everything to ensure you HAVE to buy their overpriced masks as well after buying their ridiculously priced machines.
I don't believe anything I hear and only half of what I see
Post Reply Post Reply




Possibly Related Threads...
Thread Author Replies Views Last Post
  tear down of Philips Respironics PR System One AUTO 750P mraroid 5 110 1 hour ago
Last Post: Sleepster
  [CPAP] trigger setting for ResMed aircurve 10 vauto dwbenziger 5 151 07-25-2017, 04:12 PM
Last Post: Sleeprider
  [Equipment] PR System One AUTO 750P going into service mode (no access to set up) mraroid 33 617 07-24-2017, 02:25 PM
Last Post: Sleeprider
  [Pressure] Help with Pressure Setting Vesimir 7 243 07-20-2017, 09:32 PM
Last Post: DavePaulson
  Mask type setting on Dreamstation? speed3914 1 149 07-13-2017, 08:17 PM
Last Post: Russatrice
  [CPAP] FlashAir III w/ PR System 1 A-Flex markn62 11 404 07-09-2017, 06:55 PM
Last Post: markn62
  nuance to Swift FX for her setting problems akdog30 12 670 06-24-2017, 12:10 PM
Last Post: jsielke

Forum Jump:

New Posts   Today's Posts




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.