Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

ResMed S9 Tubing to Respironice Full Face Mask
#1
ResMed S9 Tubing to Respironice Full Face Mask
I had a 10 ft. tube. It developed a hole in it. I had a Roscoe SBT-CPAP10 that I bought some time ago as a backup. When I tried installing it I found that it did not have the required adapter to fit my Respironics Full Face Mask. I was able to patch the leaky one up until I can contact my DME on Monday. The ten foot hose that I had that leaked was supplied by a DME that no longer exists so I can't get a part number for it. Does anyone know of a 10 ft. tubing that will connect to the quick disconnect on the Respironics full face mask? Thanks, Bob.
Post Reply Post Reply
#2
RE: ResMed S9 Tubing to Respironice Full Face Mask
(08-25-2013, 10:50 PM)BobF Wrote: When I tried installing it I found that it did not have the required adapter to fit my Respironics Full Face Mask.

Hi BobF,

I think all CPAP hose ends which connect to the mask are standard (are all the same).

If an adapter is required, maybe the adapter is actually part of the mask which has remained stuck in the old hose?

Perhaps you can work the old hose off of the adapter so you can use the adapter with the new hose?

Take care,
--- Vaughn
The Advisory Member group provides advice and suggestions to Apnea Board administrators and staff on matters concerning Apnea Board operation and administrative policies.  Membership in the Advisory Member group should not be understood as in any way implying medical expertise or qualification for advising Sleep Apnea patients concerning their treatment.
Post Reply Post Reply
#3
RE: ResMed S9 Tubing to Respironice Full Face Mask
(08-25-2013, 11:07 PM)vsheline Wrote:
(08-25-2013, 10:50 PM)BobF Wrote: When I tried installing it I found that it did not have the required adapter to fit my Respironics Full Face Mask.

Hi BobF,

I think all CPAP hose ends which connect to the mask are standard (are all the same).

If an adapter is required, maybe the adapter is actually part of the mask which has remained stuck in the old hose?

Perhaps you can work the old hose off of the adapter so you can use the adapter with the new hose?

Take care,
--- Vaughn

Hi Vaughn. You are right. The adapter is part of the mask. I was able to work the adapter off the old hose. I am going to buy a couple of spare hoses on Monday. Thanks a lot. I thought that the hose end adapter was molded onto the hose. Regards, Bob.

Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Full Face Mask Recommendations for Minimal Bounce with Pressure Support Unkikonki 15 530 03-14-2024, 03:00 PM
Last Post: RLRoth
  [News] Fisher and Paykel Evora Full SarcasticDave94 155 16,614 03-06-2024, 09:03 AM
Last Post: SheShells23
  Pros/Cons of buying PAP at full price TwoFistedWonderBrain 14 703 02-24-2024, 10:39 AM
Last Post: TwoFistedWonderBrain
  Flow Limitations Full Face Mask vs Pillows wickedsleepy 4 402 02-23-2024, 10:44 AM
Last Post: wickedsleepy
  [CPAP] Dry mouth despite humidifier and full face mask Tactful3149 2 448 02-13-2024, 03:25 PM
Last Post: Tactful3149
Angry [Health] I have to tighten my mask so badly that my face gets puffy... CantSleepWell 10 596 02-11-2024, 07:05 PM
Last Post: robbob2112
  Neck, face pain relef/exercises Weegie 0 169 02-11-2024, 10:16 AM
Last Post: Weegie


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.