Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

how to change pressure setting in XT Fit
#1
How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks
Reply
#2
Hi Wolfpackfan,
WELCOME! to the forum.!
I don't know the answer to your question but hang in there, someone will be able to help you, soon.
Best of luck to you as you continue your CPAP therapy.
trish6hundred
Reply
#3
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks
This might helps http://www.apneaboard.com/forums/Thread-...ex-XT-auto
Reply


#4
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks

"1. To Select CPAP or APAP Mode
1. Press "MENU" to select [Mode CPAP] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [Mode CPAP] should start
blinking to allow you to switch the mode from CPAP to APAP.
3. Press "UP" or "DOWN" button to select CPAP or APAP mode.
4. After selecting the mode, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
2. To Set the Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen in CPAP
mode.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start
blinking to allow you to adjust the therapy pressure from 4 to 20 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting. The
increment or decrement of pressure setting is 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
6. In APAP mode, follow same instructions to set the initial pressure (Pinit), maximum
pressure (Pmax), and minimum pressure (Pmin) ."
Reply
#5
(08-31-2015, 04:19 PM)Ltsail Wrote:
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks

"1. To Select CPAP or APAP Mode
1. Press "MENU" to select [Mode CPAP] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [Mode CPAP] should start
blinking to allow you to switch the mode from CPAP to APAP.
3. Press "UP" or "DOWN" button to select CPAP or APAP mode.
4. After selecting the mode, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
2. To Set the Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen in CPAP
mode.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start
blinking to allow you to adjust the therapy pressure from 4 to 20 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting. The
increment or decrement of pressure setting is 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
6. In APAP mode, follow same instructions to set the initial pressure (Pinit), maximum
pressure (Pmax), and minimum pressure (Pmin) ."

Worked like a charm with my Apex XT travel machine. Didn't have to look for the clinician manual.

Thanks for sharing.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Change p10 to n20 mask Rcgop 9 317 01-18-2017, 10:20 PM
Last Post: Sleeprider
  [Treatment] Should I change machine jm54 4 215 01-18-2017, 07:06 PM
Last Post: kwhenrykerr
  How to ulock Ramp setting on dreamstation wdriver 3 201 01-15-2017, 09:15 PM
Last Post: wdriver
  What's the maximum pressure setting that doesn't disturb your sleep? Ihaveapnea 12 528 01-14-2017, 10:02 AM
Last Post: Newbee2016
  What does the "Pressure Relief" setting? Ihaveapnea 7 313 01-07-2017, 05:12 AM
Last Post: kwhenrykerr
  Setting up DreamStation with F&P Simplus mask question grahamwright1 5 766 01-06-2017, 05:54 PM
Last Post: Jasba64
  Dreamstation Auto Bipap Setting Questions lawlipop 10 397 01-02-2017, 10:52 PM
Last Post: lawlipop

Forum Jump:




About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.

For any more information, please use our contact form.