Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

how to change pressure setting in XT Fit
#1
how to change pressure setting in XT Fit
How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks
Post Reply Post Reply
#2
RE: how to change pressure setting in XT Fit
Hi Wolfpackfan,
WELCOME! to the forum.!
I don't know the answer to your question but hang in there, someone will be able to help you, soon.
Best of luck to you as you continue your CPAP therapy.
trish6hundred
Post Reply Post Reply
#3
RE: how to change pressure setting in XT Fit
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks
This might helps http://www.apneaboard.com/forums/Thread-...ex-XT-auto
Post Reply Post Reply
#4
RE: how to change pressure setting in XT Fit
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks

"1. To Select CPAP or APAP Mode
1. Press "MENU" to select [Mode CPAP] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [Mode CPAP] should start
blinking to allow you to switch the mode from CPAP to APAP.
3. Press "UP" or "DOWN" button to select CPAP or APAP mode.
4. After selecting the mode, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
2. To Set the Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen in CPAP
mode.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start
blinking to allow you to adjust the therapy pressure from 4 to 20 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting. The
increment or decrement of pressure setting is 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
6. In APAP mode, follow same instructions to set the initial pressure (Pinit), maximum
pressure (Pmax), and minimum pressure (Pmin) ."
Post Reply Post Reply
#5
RE: how to change pressure setting in XT Fit
(08-31-2015, 04:19 PM)Ltsail Wrote:
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine? Could not find that one under the listing of other machines. Thanks

"1. To Select CPAP or APAP Mode
1. Press "MENU" to select [Mode CPAP] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [Mode CPAP] should start
blinking to allow you to switch the mode from CPAP to APAP.
3. Press "UP" or "DOWN" button to select CPAP or APAP mode.
4. After selecting the mode, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
2. To Set the Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen in CPAP
mode.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start
blinking to allow you to adjust the therapy pressure from 4 to 20 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting. The
increment or decrement of pressure setting is 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
6. In APAP mode, follow same instructions to set the initial pressure (Pinit), maximum
pressure (Pmax), and minimum pressure (Pmin) ."

Worked like a charm with my Apex XT travel machine. Didn't have to look for the clinician manual.

Thanks for sharing.
Post Reply Post Reply
#6
RE: how to change pressure setting in XT Fit
(07-03-2016, 10:28 PM)egzbuen Wrote:
(08-31-2015, 04:19 PM)Ltsail Wrote:
(11-10-2014, 01:42 PM)Wolfpackfan Wrote: How do I adjust the preset pressure setting on an APEX XT Fit cpap machine?  Could not find that one under the listing of other machines.   Thanks

"1. To Select CPAP or APAP Mode
1. Press "MENU" to select [Mode CPAP] menu while in the standby screen.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [Mode CPAP] should start
blinking to allow you to switch the mode from CPAP to APAP.
3. Press "UP" or "DOWN" button to select CPAP or APAP mode.
4. After selecting the mode, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
2. To Set the Pressure
1. Press "MENU" to select [P XX.XcmH2O] menu while in the standby screen in CPAP
mode.
2. Hold the "UP" and "DOWN" button, and then simultaneously press the "MENU"
button for one second. Meanwhile, the LCD screen [P XX.XcmH2O] should start
blinking to allow you to adjust the therapy pressure from 4 to 20 cm H2O.
3. Press "UP" or "DOWN" button to increase or decrease the pressure setting. The
increment or decrement of pressure setting is 0.5 cm H2O.
4. After selecting the prescribed pressure, press "MENU" to confirm.
5. Press “START/STANDBY” button to go back to standby screen or leave the device to
automatically go back to standby screen 20 seconds later.
6. In APAP mode, follow same instructions to set the initial pressure (Pinit), maximum
pressure (Pmax), and minimum pressure (Pmin) ."

Worked like a charm with my Apex XT travel machine.  Didn't have to look for the clinician manual.

Thanks for sharing.
Post Reply Post Reply
#7
RE: how to change pressure setting in XT Fit
Thanks, this worked great
Post Reply Post Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Setting time and date on Resmed Airsense 10 cmadon 42 32,011 03-08-2024, 09:13 AM
Last Post: Sleeprider
  AirSense 10 Max Pressure setting Tomt 13 810 03-04-2024, 07:11 PM
Last Post: Tomt
  [CPAP] Prisma 20A - Change of machine and regression elliott.981. 16 1,583 02-21-2024, 08:46 AM
Last Post: Sleeprider
  Any change recommendations to machine? NativTxn 2 306 02-17-2024, 03:28 PM
Last Post: NativTxn
  [Symptoms] Recent Symptom - Settings Change? MamaK55 1 159 02-10-2024, 06:03 PM
Last Post: Deborah K.
  [Pressure] I just started apap therapy 3 weeks ago and I feel worse.Should I change settings? AndreiChivu 1 314 02-03-2024, 08:08 PM
Last Post: Sleeprider
  [Pressure] Pressure max/min clarification and change I made richapple 5 354 01-28-2024, 04:03 PM
Last Post: richapple


New Posts   Today's Posts


About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.