FlashAir Problem? - Printable Version +- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums) +-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area) +--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum) +--- Thread: FlashAir Problem? (/Thread-FlashAir-Problem) |
FlashAir Problem? - parkerdt - 07-20-2015 I have a FlashAir W-02 16gb card for my A10 Autoset. Normally it reads properly in station mode. Recently however, the card has not been findable by FlashPAP in the mornings when I go to download my data. I have to either remove and reinsert the card or power cycle the machine. Anyone have a suggested fix for this? Thanks, Dave RE: FlashAir Problem? - DariaVader - 07-20-2015 change the timeout value to 0. Think the default is 30000 or something APPAUTOTIME=0 https://flashair-developers.com/en/documents/api/config/ RE: FlashAir Problem? - parkerdt - 07-20-2015 (07-20-2015, 02:18 PM)DariaVader Wrote: change the timeout value to 0. Think the default is 30000 or something Thanks, I've tried that without success. Here's my config: [Vendor] CIPATH=/DCIM/100__TSB/FA000001.JPG APPMODE=5 APPNAME=FlashAir APPSSID=ParkerHome 2 APPNETWORKKEY=********************************** VERSION=FA9CAW3AW3.00.00 CID=02544d535731364731d5d7737900f301 PRODUCT=FlashAir VENDOR=TOSHIBA MASTERCODE=1234567890AB LOCK=1 FORMATSETMODE=1 APPINFO=0000000000000000 APPAUTOTIME=0 STA_RETRY_CT=0 NOISE_CANCEL=0 Dave RE: FlashAir Problem? - DariaVader - 07-20-2015 I have the S9 Autoset. Perhaps it lacks some of the power saving "features" of the A10... As you know, the flashair gets power to be on from the device it is plugged into. [Vendor] CIPATH=/DCIM/100__TSB/FA000001.JPG VERSION=F19BAW3AW2.00.03 CID=02544d535731364708dd306c7800e601 PRODUCT=FlashAir VENDOR=TOSHIBA APPNAME=flashair WEBDAV=0 TIMEZONE=-28 APPSSID=DARIANET APPNETWORKKEY=********* APPMODE=5 APPAUTOTIME=0 DNSMODE=1 LOCK=1 UPLOAD=1 RE: FlashAir Problem? - DariaVader - 07-20-2015 Something else to try.... https://sleep.tnet.com/resources/sleepmaster/zflashairfix Wrote:FlashAir Fix for Close Signal Issues RE: FlashAir Problem? - parkerdt - 07-20-2015 My AP is about 20 feet away through 2 walls, but can't hurt to try! Thanks! RE: FlashAir Problem? - DariaVader - 07-20-2015 I think it is more likely that the A10 is "green" and is not powering the flashair sufficiently to keep it online, but idk. Not likely to be "noise" at that distance, IMO. This might be the first time I am happy I got the older S9 rather than the A10 RE: FlashAir Problem? - parkerdt - 07-20-2015 I don't know - seems to stay up during the day - I've been hitting it with FlashPAP off and on to see if it has gone away; it has not, and I know my A10 is in powersaving mode. We'll see what happens in the AM! Thanks again, Dave RE: FlashAir Problem? - AlanE - 07-20-2015 I occasionally have that issue after I stop using the machine and try to download the data. There is no rhythm or reason for it and it doesn't happen every day. I do notice that when I have a power failure (however brief) I have to reinsert the card to connect it with the network again. Do you have your router set to cycle off/on during the night? RE: FlashAir Problem? - parkerdt - 07-20-2015 No, my router and CPAP are both on UPS supplies, actually. Enough to ride out any outage of an hour and a half or less. |