+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Airsense Autoset 10, "Error: power connector in rear is not plugged in" (/Thread-Airsense-Autoset-10-Error-power-connector-in-rear-is-not-plugged-in)
Airsense Autoset 10, "Error: power connector in rear is not plugged in" - Possum - 04-11-2016
I came home to that error message, out of the blue, reached back to ensure that cord was plugged in completely, then power blacked out, never to return. I quickly realized that the back connector was wet, and appeared to have been wet for awhile. I tried to no avail to dry it with q-tips, hair dryer, etc. It's still shorted out.
Does anyone have any ideas on how this could have happened? The machine has never been dropped. I do keep it on the floor so that condensation drains back into the water tank, but it never occurred to me that it could somehow drain into the machine itself, unless the heated hose connection is not 100% sealed, but I would think that would show up as a fairly large leak. I have noticed higher than normal leak rates (2-7 L/min, as displayed on machine itself), but thought that could have been attributed to a dud replacement nose pillow.
So it looks like I'll be without therapy for awhile, until I can get an appointment at my DME... I guess if I had any doubts about whether PAPing was helping me, the next few nights will be quite telling.
Guess I can also use it as a chance to collect some baseline SPO2 data to see how bad my oxygen levels without therapy.
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - sdb7802 - 04-11-2016
That error usually means the center pin signal is missing. The power plug is a three conductor plug: an outer shell (+24V), an inner shell (common), and a slender center pin (+3.3V). If you've got a voltmeter you can check the voltages.
Sometimes the center pin gets bent and doesn't make contact.
The power supply will usually recover from a short by cycling it. I've shorted it before, unfortunately.
The water could have fried it.
I'd check the pin and dry the plug and socket again. The machine internals may dry out overnight.
I know that's not much help.
Steve
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - Possum - 04-11-2016
I think you're 100% correct. The central pin is gone, appears to be fried. Can't believe I didn't observe that right off the bat. That also explains why there's so much black soot coming out of the plug - that's what remains of the central pin. Now the question is, how in the hell did water get in the electrical area, enough to fry the electronics?
In any case, here's to a couple of sleepless nights until I can get in to my forsaken DME. :-|
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - sdb7802 - 04-11-2016
I think hose connector (the part you squeeze) is a half-ass design.
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - Possum - 04-11-2016
(04-11-2016, 11:30 PM)sdb7802 Wrote: I think hose connector (the part you squeeze) is a half-ass design.
So are you thinking condensation has been leaking into the machine through the hose, and eventually fried the electronics? That's what I was thinking, but I always assumed the hose formed a pretty good seal.
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - sdb7802 - 04-12-2016
(04-11-2016, 11:34 PM)Possum Wrote: So are you thinking condensation has been leaking into the machine through the hose, and eventually fried the electronics?
Do you remember what your humidifier setting was?
If the hose was loose, the water could have pooled around the power entry. That would take a lot of water.
Or maybe there's a crack in the internal plumbing.
(04-11-2016, 11:34 PM)Possum Wrote: I always assumed the hose formed a pretty good seal.
It is if it's fully seated. Just kind of flimsy. Might not leak after all. Most of the design is pretty impressive. There's always something that causes problems. Nothing would surprise me.
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - Possum - 04-12-2016
(04-12-2016, 12:01 AM)sdb7802 Wrote: Do you remember what your humidifier setting was?
I keep humidity on 5 and hose temp maxed out at 86 deg F, but sometimes I still get condensation. Thought I was being clever by keeping the machine low so it would drain back into the tank. I guess this is what happens..
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - sdb7802 - 04-12-2016
Is your water tank leaking?
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - Possum - 04-12-2016
(04-12-2016, 12:16 AM)sdb7802 Wrote: Is your water tank leaking?
Don't think so.. But I wonder if I overfilled it and that caused water to enter the electronics module when the blower came on.
RE: Airsense Autoset 10, "Error: power connector in rear is not plugged in" - trish6hundred - 04-12-2016
Hi Possum,
I’m sorry to hear about your machine, hopefully, you can get in to see the DME really soon.
Good luck to you.