+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Sudden pressure jump - fixable? (ResMed) (/Thread-Sudden-pressure-jump-fixable-ResMed)
Sudden pressure jump - fixable? (ResMed) - illustr8r - 04-29-2017
I'm using a ResMed S9. My data card corrupted a couple years ago, so I removed it and haven't replaced it, so I can't provide any data here, unfortunately.
My problem is that the machine just BLASTS so strongly that I cannot use it any more. It went into blast mode a few months ago, and I quit using it until I could get it fixed or get a new one. Then I plugged it in "one last time" before going through the supreme hassle to get a new one, to see if it might work, and go figure - it was fine again!
So now I've been back on it for about a week. And last night I was using it, and during the night I had an itch on my nose, so I broke the seal of the mask with my finger to scratch it - just for a second - and the machine went into Leaf-Blower mode again, just blasting, and wouldn't die back down.
I suspect there's a pressure regulator sensor or something that has failed, or is getting stuck, where the machine is improperly sensing exactly how much pressure it is putting out. I have no idea, and cannot find out anything about how to troubleshoot and fix this myself, if I can. I've had the machine for slightly more than 5 years. I guess I can get a new one, but as I understand it, I'll have an insane out-of-pocket co-pay that I want to avoid if I can. Do I need to just bite the bullet and ship the thing off, or is this something I can diagnose and fix myself? I've combed the web for info, and have found nothing.
RE: Sudden pressure jump - fixable? (ResMed) - C0mbe - 04-29-2017
It's hard to say anything without data. i have found that uncontrolled leaks can really cause "leaf blower" mode, particularly on Resmed machines. If you were recording data, or willing to start recording data again we could rule out legitimate causes of pressure increases before jumping to "broken."
If you are thinking new machine, I would go Airsense 10 Autoset and a good place to look is Supplier # 2.
RE: Sudden pressure jump - fixable? (ResMed) - Mosquitobait - 04-29-2017
Suppliers 27 and 28 repair cpap machines. You could ask about service as to whether your problem is likely a board problem or something else. Replacing a board for a machine that has over 15,000 hours is probably not worth it, but I don't know the pricing.
Since you have a high deductible, I would consider getting either a used machine (you can find low hours) or a script and buy from an online retailer. Some have open box policies that include warranty, so good if that is the way you want to go.
RE: Sudden pressure jump - fixable? (ResMed) - trish6hundred - 04-29-2017
Hi illustr8r,
WELCOME! to the forum.!!
Which S9 machine do you have? I think the name is under the on/off button.
They have some good deals on either open-boxed, or gentally-used machines at Supplier #2. Hopefully, you have a copy of your prescription.
Hang in there for more responses to your post and good luck to you with getting your machine problem straightened out.
RE: Sudden pressure jump - fixable? (ResMed) - justMongo - 04-29-2017
(04-29-2017, 07:55 AM)illustr8r Wrote: I suspect there's a pressure regulator sensor or something that has failed, or is getting stuck, where the machine is improperly sensing exactly how much pressure it is putting out. I have no idea, and cannot find out anything about how to troubleshoot and fix this myself, if I can. I've had the machine for slightly more than 5 years. I guess I can get a new one, but as I understand it, I'll have an insane out-of-pocket co-pay that I want to avoid if I can. Do I need to just bite the bullet and ship the thing off, or is this something I can diagnose and fix myself? I've combed the web for info, and have found nothing.
If the above is true, there is little you can do about it. What the machine knows about pressure and flow comes from two pressure sensors. One located near the blower unit's outlet; and another just a little upstream with a coarse mesh separating the two. The downstream sensor is used as the primary pressure sensor. The upstream sensor is used in differential with the downstream to calculate flow. The mesh (or grid pattern) creates an impedance to flow such that the pressure differential is proportional to flow. The pressure sensors have no actual moving parts -- they are piezoresistive. So, they cannot get stuck.
Sometimes it's water that kills these sensors; but the H5i was well designed to help prevent water from backflowing into the blower unit. Getting the parts is nearly impossible.
RE: Sudden pressure jump - fixable? (ResMed) - Mogy - 04-29-2017
SD cards are fairly cheap.
What are the pressure settings on the machine? I don't know how to determine that on your machine, but it can't be difficult.
What about lowering the upper pressure? If that was set quite high, the machine may have decided you need the higher pressure now.
RE: Sudden pressure jump - fixable? (ResMed) - Sleeprider - 04-29-2017
Don't overlook that you can buy a new Dreamstation Auto on Amazon for less than the costs of repairs to your S9, about $340. Deals on the Airsense 10 are all over the place, and don't overlook the Craigslist ads for machines at $495-525 that are new. Double check, but most are legimate dealers offering equipment well below minimum advertised price and using Craigslist where the manufacturers won't yank their franchise rights.