+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Rise Time on Respironics BiPAP ST (PR Sys One) (/Thread-Rise-Time-on-Respironics-BiPAP-ST-PR-Sys-One)
Rise Time on Respironics BiPAP ST (PR Sys One) - InfiniteReality - 11-06-2012
Hi, first thanks for this great site and thanks to supersleeper for the clinicians manuals!
I got a new BiPAP ST, the respironics PR System One last week. It's great except I can't sleep with it and my old one is pretty much shot. The only difference I can really tell is the rise time on the new one is longer than the old one. The old one (also a respironics) is set at a 100ms rise time (it has options of 1-6, 1 is 100ms). The new one only has options 1-3 and it feels like the 1 setting is twice as long as the old one (200ms). And I think this is my problem. The clinicians manual for the new machine doesn't specify what the 1-3 correspond to for the PR Sys One bipap st.
Does anyone know what the 1-3 correspond to? And is there a way to change it to 100ms, maybe via software? I didn't see anything on the sleepyhead software, but would the official software be able to do this? Or some other way?
Settings are IPAP 17, EPAP 4, BPM 16, inspiratory time 1.8 secs, rise time 1
Note: I pretty much use the backup rate all the time when sleeping (due to muscular dystrophy).
Thanks!
Mike
RE: Rise Time on Respironics BiPAP ST (PR Sys One) - Sleepster - 11-06-2012
Are you sure the manual doesn't specify the rise time? I seem to recall that the 1, 2, and 3 corresponds to 200 ms, 400 ms, and 600 ms respectively, but I couldn't swear to it.
I googled "bipap st rise time" and found this on the second hit:
"The Rise Comfort is the time for the device to shift from EPAP to IPAP and can be adjusted in 150, 200, 300, 400msec."
At any rate, if you've got it set as low as it'll go I'm sure you'll adjust to it after a bit. It's supposed to be just a comfort setting. Have you fiddled with the Bi-Flex setting. I think the factory default is 2, so you might try lowering that to 1. I think it also changes the shape of the pressure curve. You should be able to read about all this in the clinician's manual.
RE: Rise Time on Respironics BiPAP ST (PR Sys One) - InfiniteReality - 11-06-2012
Thanks for the response! I looked at that link and the picture is a little different than mine. the center plate is dark/black on mine, so it might be different. But mine only has 3 settings. And the therapist that delivered the machine left the clinicians manual in it, and it doesn't mention any specifics on the rise time. The manual is the same as the one I downloaded here.
I looked at the Bi-Flex and it is only for S mode, and I'm using S/T, and mostly in the timed part of the ST.
The problem is that I feel like I'm not getting enough oxygen with the current settings, hopefully I'll get used to it soon, but will be seeing the sleep doc again this friday..
Is there a way to get the EncorePro software? I'm wondering if that might be able to set what the numbers refer to.
RE: Rise Time on Respironics BiPAP ST (PR Sys One) - Sleepster - 11-06-2012
What's the model number of your machine?
RE: Rise Time on Respironics BiPAP ST (PR Sys One) - trish6hundred - 11-06-2012
Hi InfiniteReality and WELCOME! to the forum.!
Best of luck to you with your new machine.
RE: Rise Time on Respironics BiPAP ST (PR Sys One) - InfiniteReality - 11-06-2012
Thanks for the welcome!
It says BiPAP S/T, C-Series, DOM on the bottom
REF: 1061401
My mom called respironics and talked to a clinician. They said none of the current models of bipaps support lower than 200ms. The 1-3 corresponds to 200, 300, 400ms. So at least that verifies what I was feeling and I can tell the sleep center they are wrong when they say the settings are the same as the old one.
At least last night I slept for a few hours.