+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Philips Respironics DreamStation check power (/Thread-Philips-Respironics-DreamStation-check-power)
Pages:
1
2
Philips Respironics DreamStation check power - Steve Foley - 11-08-2020
I have a Philips Respironics DreamStation which has worked well for about 2 years now. On Friday 06 Nov 2020 I switched on and it displayed the usual Opening Image then Menu Icons on the Screen but after a few seconds a larger Icon appeared "check power" with the image of a Power Brick (PSU) appeared but nothing worked although the Screen remained on for a while and the On/Off switch symbol flashed on and off. I tried unplugging the PSU, leaving it for a few hours then plugged it back in but it went through the same boot up process and displayed "check power" again and would do nothing.
I then checked the Power Brick with a DVM and it showed 12.25 VDC off load. I then tried a Laptop PSU of my own with the correct type of plug but with the same result.
Is this fault truly related to the Power Brick that came with the DreamStation in which case I can afford to buy a replacement or is it an internal fault on the Printed Circuit Board, a faulty Sensor, a non functional Internal Battery, the Internal Blower failing or whatever? I am an Electronics Technician so I understand Circuitry etc but I have not opened the Unit. I have downloaded the User Manual but is there a Servicing and Repair Manual for this CPAP Unit? If this failure message is spurious is there a way to Reboot the Unit or Force a Boot up as is possible with many Computers and Electronic Equipment?
I'm rather new here so if this post is on the wrong Forum please advise me and I will cut and paste it to the correct one.
Thanks in advance.
RE: Philips Respironics DreamStation check power - OpalRose - 11-08-2020
There are Service Manuals for the DreamStation in the Private Files and Links Forum.
Good luck... hope that helps!
RE: Philips Respironics DreamStation check power - Steve Foley - 11-08-2020
Thanks. I'll look there.
RE: Philips Respironics DreamStation check power - fitzspr5224 - 11-16-2020
My situation is a mirror of yours, including when you started cpaping except i left my machine on with power supply error message and about 6 hours i got a message that now says "the attached power supply does not support humidification" and appears to run, i have not tried it with water yet. i appreciate all the work you are doing on this issue. my machine worked fine until last night when i reset it up after a 1000 mile trip from my sisters house, i guess the power supply had a rough journey. Looks like it could be a power supply issue which is kinda surprising, have worked with hundreds of electronics and bad power supply is unusual to me.
RE: Philips Respironics DreamStation check power - SarcasticDave94 - 11-16-2020
Depending on the length of time you've owned the PAP, it may be that the issue is covered under warranty. I'd follow up with the DME supplier you got this from.
RE: Philips Respironics DreamStation check power - fitzspr5224 - 11-17-2020
Working with KPs contract support vendor we have apparently resolved my lssue. It appears the issue was due some issue with the heated hose, perhaps not completely engaged in coupling or ?, but replacing the hose with my spare fixed the problem and going back to the original heated hose, it is still working.
RE: Philips Respironics DreamStation check power - Steve Foley - 11-29-2020
I am also a Electronics Service and Calibration Technician. I tested the Power Brick PSU with a good DVM an the voltage seem to be correct. However that was off load so I obtained another brand new PSU and alas the same error Message. "Check Power". So it is either a faulty component on a PCB, a damaged Sensor, or a Software/Firmware related fault. Is there either Global Reset to Default Settings command or a way to force a boot up ignoring the Error Message?
RE: Philips Respironics DreamStation check power - Dandydog - 04-22-2021
Steve -
Did you ever get anywhere with this problem?
We’ve got the same thing happening
(‘Check Power’ screen), and replacing the ‘Power Brick’ (!?) and cord didn’t change the situation.
Neil
Philips Dreamstation ‘Check Power’ problem - Dandydog - 04-22-2021
I’m trying to get past a ‘Check Power’ screen on a Dreamstation CPAP.
We’ve replaced the ‘Power Brick’ and cord without correcting the problem: with either power source, the display cycles through a number of set-up screens when plugged in, then reverts to the ‘Check Power’ display and stays there. Shaking the machine doesn’t help.
The ‘Bricks’ have identical model numbers, and are labeled “Manufactured for Respironics Inc.” and “Distributed by: Respironics Inc.” The new unit was ordered from Direct Home Medical.
I ran across the following warning on another forum:
“Read this statement:
"While Respironics DreamStation Series devices operate from 12V direct
current, the DC port on these devices require a proprietary signal in order
to recognize a valid power source; therefore, the use of a 12V power
adapter is required in order for the CPAP Battery to power these devices."”
Can anyone validate that information? Has anyone got a solution to this problem? [Steve: Did you get anywhere with your effort?]
(Philips is unresponsive; DHM says it’s Philip’s problem.)
Any suggestions will be greatly appreciated, and the solution - if found - will be posted.
Thanks - Neil
RE: Philips Respironics DreamStation check power - Crimson Nape - 04-22-2021
Dandydog - Your thread has been merged into an existing thread about the same subject.