+- Apnea Board Forum - CPAP | Sleep Apnea (https://www.apneaboard.com/forums)
+-- Forum: Public Area (https://www.apneaboard.com/forums/Forum-Public-Area)
+--- Forum: Main Apnea Board Forum (https://www.apneaboard.com/forums/Forum-Main-Apnea-Board-Forum)
+--- Thread: Auto mode and data versus exact mask (/Thread-Auto-mode-and-data-versus-exact-mask)
Auto mode and data versus exact mask - PaytonA - 01-08-2014
I am currently using a ResMed S8 VPAP 25 Auto which the DME set up in (S)pontaneous mode. They also supply me with an F & P Zest nasal mask which is vented. The ResMed VPAP has a setting for the mask in use, Mine is set to Ultra which is the factory setting. Naturally the only masks listed in the selection menu are ResMed masks. Does this setting make any difference for any of the calculated results?
I am also thinking of switching to the auto mode. Again will the fact that the mask that I use is not a choice in the settings menu make a difference in the way the VPAP reacts in auto mode?
My concern is that the exact size of the vents might make a difference to some of the calculated parameters that the VPAP uses or that I want to use once I receive the card reader that I ordered.
Thanks in advance for any info on this.
PaytonA
RE: Auto mode and data versus exact mask - zonk - 01-08-2014
Check mask guide and see how Zest vents flow rate compare to Resmed nasal masks vents flow rate
Resmed masks http://www.resmed.com/assets/documents/service_support/pressure_flow_rates/1012648_pressure-vs-flow_usa_eng.pdf
Probably not much difference. With the S9, Resmed grouped all nasal masks together and "Nasal" is the mask selection (maybe, Standard - S8 equivalent) with couple of exceptions Ultra Mirage and Swift FX Nano
RE: Auto mode and data versus exact mask - PaytonA - 01-08-2014
The flow rate for the vents on my Zest at my IPAP is 43 l/min and for the ResMed Ultra is 53 l/min. This seems to me like it would make a difference. What do you think?
PaytonA
RE: Auto mode and data versus exact mask - zonk - 01-08-2014
(01-08-2014, 08:01 PM)PaytonA Wrote: The flow rate for the vents on my Zest at my IPAP is 43 l/min and for the ResMed Ultra is 53 l/min. This seems to me like it would make a difference. What do you think?I would change it to Standard or Activa
PaytonA
Because Resmed nasal masks vents leak rate 45 L/m at 20 which correspond with Zest vents leak rate at the same pressure
S8 report leak in L/s ... 24L/m = 0.4 L/s
RE: Auto mode and data versus exact mask - PaytonA - 01-09-2014
(01-08-2014, 04:22 PM)zonk Wrote: Check mask guide and see how Zest vents flow rate compare to Resmed nasal masks vents flow rate
Resmed masks http://www.resmed.com/assets/documents/service_support/pressure_flow_rates/1012648_pressure-vs-flow_usa_eng.pdf
Probably not much difference. With the S9, Resmed grouped all nasal masks together and "Nasal" is the mask selection (maybe, Standard - S8 equivalent) with couple of exceptions Ultra Mirage and Swift FX Nano
I checked the mask guide (thanks for the link) and found that the ResMed Swift mask had the closest vent flow rate to the F&P Zest. I put that in the setting for mask type and this morning read 2.7 AHI for last night. My normal has been in the 5's recently although I do not get around to reading the daily results early enough that the day has not been reset. I do not have a data card reader yet but have one on order. I will see how it goes.
Thanks for the help,
PaytonA
RE: Auto mode and data versus exact mask - PsychoMike - 01-09-2014
The setting probably won't have any impact on the AHI reading, or if it does, it'd be minimal at best....Resmed machines use the setting to calculate the unintentional leak rate (total leak rate - intentional (or venting) = unintentional leak rate).