I noted on the Machine Settings section of SleepyHead there is a "Temp. Enable -2". Do not use a heated tubing and the Humidity Level is set at -3.
Anyone know where this is adjusted or what it is?
Hello Guest,
Welcome to Apnea Board !
ResMed TEMPERATURE ENABLE
|
11-11-2017, 01:45 PM
ResMed TEMPERATURE ENABLE
Temperature Enable
I noted on the Machine Settings section of SleepyHead there is a "Temp. Enable -2". Do not use a heated tubing and the Humidity Level is set at -3. Anyone know where this is adjusted or what it is?
11-12-2017, 10:30 AM
RE: ResMed TEMPERATURE ENABLE
Above TEMPERATURE ENABLE is TEMPERATURE 27C (being 80.6F). Must be machine temp sensor somewhere in the system as room temp is nowhere near that. But the 2 seems to indicate a variability setting.
Dumb question or no one knows?
11-12-2017, 10:46 AM
RE: ResMed TEMPERATURE ENABLE
Not a dumb question.
I’m not a ResMed user, but will take a stab at answering. Just from browsing the Clinicians Manual, page 10...I assume this is referring to the temperature of the hose, and how the machine maintains the set tube temperature. Tube Temperature If the air in the mask feels too warm or too cold, the patient can adjust the temperature to find what is most comfortable or turn it off completely. The Tube Temperature can be set to anywhere between 60–86°F (16–30°C). The temperature sensor located at the mask end of the ClimateLineAir heated air tubing enables the system to automatically control the temperature of the air delivered to the patient. This ensures the temperature of the air delivered to the patient does not fall below the set minimum temperature, therefore maximizing breathing comfort for the patient.
OpalRose
Apnea Board Administrator www.apneaboard.com _______________________ OSCAR Chart Organization How to Attach Images and Files. OSCAR - The Guide Soft Cervical Collar Optimizing therapy OSCAR supported machines Mask Primer INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
11-12-2017, 10:50 AM
RE: ResMed TEMPERATURE ENABLE
To change this go to the clinical settings and under comfort. The one is the temperature of the hose abt the other no. 1 to 4 is the amount of moisture.
11-12-2017, 12:14 PM
RE: ResMed TEMPERATURE ENABLE
(11-12-2017, 10:46 AM)OpalRose Wrote: Tube Temperature Thanks for the response but I believe it indicates the sensor is in the ClimateLineAir heated hose -this is using a slim-line unheated hose; no sensor. Maybe when the heated hose is plugged in it automatically enables internal software/ meaning the settings shown are moot (not actually actuated)?
11-12-2017, 12:20 PM
RE: ResMed TEMPERATURE ENABLE
(11-12-2017, 10:50 AM)Gary1of2 Wrote: To change this go to the clinical settings and under comfort. The one is the temperature of the hose abt the other no. 1 to 4 is the amount of moisture. Just checked my AirCurve 10 Vauto and as far as I can determine it shows only humidity (water tub adjustment) 1-8. It is set at 3 and is accessible through the clinical or patient accessed adjustments. I have no heated hose. Maybe additional adjustments only appear when the heated hose is attached? Thanks
11-12-2017, 01:46 PM
RE: ResMed TEMPERATURE ENABLE
(11-12-2017, 12:14 PM)zzzZorro Wrote:(11-12-2017, 10:46 AM)OpalRose Wrote: Tube Temperature Right, all heated hoses have a sensor where it connects to the mask. I didn’t know what type of hose you were using, so the setting probably doesn’t apply.
OpalRose
Apnea Board Administrator www.apneaboard.com _______________________ OSCAR Chart Organization How to Attach Images and Files. OSCAR - The Guide Soft Cervical Collar Optimizing therapy OSCAR supported machines Mask Primer INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
11-12-2017, 09:28 PM
RE: ResMed TEMPERATURE ENABLE
(11-12-2017, 12:20 PM)zzzZorro Wrote:(11-12-2017, 10:50 AM)Gary1of2 Wrote: To change this go to the clinical settings and under comfort. The one is the temperature of the hose abt the other no. 1 to 4 is the amount of moisture. That is correct. It is the temperature of the hose. |
« Next Oldest | Next Newest »
|
Possibly Related Threads... | |||||
Thread | Author | Replies | Views | Last Post | |
CSA, Body temperature and Spicy foods. | Boodmaster | 4 | 796 |
03-26-2024, 02:29 AM Last Post: Boodmaster |
|
How do I enable autoset on a ReMed Airsense 10 elite | krschultz | 3 | 581 |
09-25-2023, 06:17 PM Last Post: Gideon |
|
AirSense11 temperature regulation | Lostsleep | 25 | 7,882 |
10-23-2022, 01:18 PM Last Post: M Friedman |
|
Forgot to slide the write-enable tab on the SD card AGAIN! | cathyf | 2 | 619 |
07-03-2022, 09:35 PM Last Post: greatunclebill |
|
Resmed AirSense 10 Heater Plate Temperature | JerryK | 30 | 6,098 |
11-12-2021, 07:53 AM Last Post: Chriheat |
|
[Equipment] Resmed Climateline Temperature Auto | GrandpaSteve | 2 | 758 |
10-08-2021, 10:33 AM Last Post: GrandpaSteve |
|
Tube Temperature | SwirlySauce | 7 | 1,373 |
05-25-2021, 09:26 AM Last Post: biorn |