Hello Guest, Welcome to Apnea Board !
As a guest, you are limited to certain areas of the board and there are some features you can't use.
To post a message, you must create a free account using a valid email address.

or Create an Account


New Posts   Today's Posts

Resmed aircurve 10 asv setup
#1
Resmed aircurve 10 asv setup
Hi guys so I bought a resmed aircurve asv 10 from someone ,,has less than 100 hrs, Can u guys recommend basic settings for me to try it out. I have centrals and osa both moderate. I do have centrals around 6cm not sure if that matters. I did post some of my previously studies with apap on here. Let me kno
Post Reply Post Reply






Donate to Apnea Board  
#2
RE: Resmed aircurve 10 asv setup
FWIW If you choose ASV Auto that gives you 4 settings for pressure as follows:

EPAP Min and Max.

Pressure Support (PS) Min and Max.

IPAP will be variable as the sum of EPAP and PS.

If you run it as ASV, it reduces settings to EPAP (w/o Min or Max) and PS Min and Max

Obviously, there are comfort settings as well.

What did you have set on the prior machine? This would help us fill in the blanks. You mentioned prior posts with images, so I'll try to find them.
Dave

OSCAR
Standard OSCAR Chart Order
Mask Primer
Dealing With A DME
Soft Cervical Collar Wiki
INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEBSITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply
#3
RE: Resmed aircurve 10 asv setup
https://www.scribd.com/document/35340282...-Titration
From the titration guide, you can use some of your existing settings or titrate it as you go, but the default would be
min epap 4
max epap 15
min ps 3
max ps 15
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
For auto-cpap, from machine data or software. You can set the min pressure 1 or 2cm below 95%. Or clinicians commonly use the maximum or 95% pressure for fixed pressure CPAP, this can also be used for min pressure.
https://aasm.org/resources/practiceparam...rating.pdf
Post Reply Post Reply
#4
RE: Resmed aircurve 10 asv setup
The settings suggested by ajack are default for ASV titration. If you needed higher settings for obstructive apnea on CPAP it might vary. Take a look at this:

[Image: liakbFr.png]
Sleeprider
Apnea Board Moderator
www.ApneaBoard.com

____________________________________________
Download OSCAR Software
Soft Cervical Collar
Optimizing Therapy
Organize your OSCAR Charts
Attaching Files
Mask Primer
How To Deal With Equipment Supplier


INFORMATION ON APNEA BOARD FORUMS OR ON APNEABOARD.COM SHOULD NOT BE CONSIDERED AS MEDICAL ADVICE. ALWAYS SEEK THE ADVICE OF A PHYSICIAN BEFORE SEEKING TREATMENT FOR MEDICAL CONDITIONS, INCLUDING SLEEP APNEA. INFORMATION POSTED ON THE APNEA BOARD WEB SITE AND FORUMS ARE PERSONAL OPINION ONLY AND NOT NECESSARILY A STATEMENT OF FACT.
Post Reply Post Reply






Donate to Apnea Board  
#5
RE: Resmed aircurve 10 asv setup
Thanks guys will post results soon
Post Reply Post Reply
#6
RE: Resmed aircurve 10 asv setup
So I started my therapy on my asv with the default settings listed above in asv auto mode. I tried the therapy for about an hour or so and ended up swallowing a lot of air. Funny thing is I don't really recall falling asleep, although the machine did wake me up several times with higher pressures probably as I was starting to drift, needless to say spent the next few hours getting rid of the unwanted air
Post Reply Post Reply
#7
RE: Resmed aircurve 10 asv setup
Had a few images from my 1hour , not sure if it's my computer or just a bug but the, file ,view ,data ,tabs ,help tabs at top left of sleepyhead will not give me drop down menus. So was not able to do the tradition screen shot. Took a few pics instead

https://imgur.com/a/Zq1et
Post Reply Post Reply






Donate to Apnea Board  
#8
RE: Resmed aircurve 10 asv setup
One of the joys of ASV variable pressure. Smile
why are you swapping from your auto 10? You may be better on that machine, if it wasn't recommended by the doctor to change. They normally have a titration to show that you need it and echocardiogram to check your heart, so bad things don't happen. You can't go by that chart as you were awake and it was for an hour. There may be enough to move min epap to 6, sleeprider did ask what you cpap pressures were.
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
For auto-cpap, from machine data or software. You can set the min pressure 1 or 2cm below 95%. Or clinicians commonly use the maximum or 95% pressure for fixed pressure CPAP, this can also be used for min pressure.
https://aasm.org/resources/practiceparam...rating.pdf
Post Reply Post Reply
#9
RE: Resmed aircurve 10 asv setup
Hey Ajack ,
Yes I've had a sleep study that shows that standard apap will not work as it causes more central apneas for me. I actually just had a another study last week but the tech didn't listen to me and we did another titration with cpap. She did say that it did not work and I would need either bipap or asv ,which is what I had already told her. She said she did it because insurance purposes.
Anyway I'm sure they will be calling wanting me to spend another night in there facilities. My road in dealing with this has been quite long, that's why I just got my own machine, these drs take forever to do anything. I have had an echo and my heart is normal. I was just wondering if I can turn down the pressure so I don't swallow so much air. In order to do that do I just take asv auto off and just put it on asv and change the settings? I just don't know how I can get any data if I can't keep the thing on. I think I clear obstructs at 10 to 15 but centrals start at around 6cm
Post Reply Post Reply
#10
RE: Resmed aircurve 10 asv setup
any treatment is better than no treatment, to choke down the ASV, I would have min epap 6 max epap 10,
the min PS I would leave at 3 for now, the max PS I would choke back to 10. Looking at your chart, if that was for a whole night, you would have a pressure swing from 6 to 18

You need some hours of sleep on the ASV, to get some data to see where to go. we are still flying blind. All UA and H are obstructive and are treated with min epap in the end. Then you need to zoom in and see if the CA are getting enough PS, there is enough tidal volume and flow. You can also see what is the min PS you feel comfortable with and still keep good stats. sleeprider suggests a min PS of 1 if the stats allow it. In the thought of reducing the number of centrals that are pressure induced.
mask fit http://www.apneaboard.com/wiki/index.php...ask_Primer
For auto-cpap, from machine data or software. You can set the min pressure 1 or 2cm below 95%. Or clinicians commonly use the maximum or 95% pressure for fixed pressure CPAP, this can also be used for min pressure.
https://aasm.org/resources/practiceparam...rating.pdf
Post Reply Post Reply






Donate to Apnea Board  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Aircurve 10 instead of Airsense 10 for her dreamers 3 153 8 hours ago
Last Post: SakimaStorm
  Moving from a Dreamstation Bipap to Resmed Aircurve 10 Vauto xamax 9 154 08-01-2021, 01:49 PM
Last Post: xamax
  AIRCURVE 10 CHANGE THAT WORKED CROWMAN 1 115 08-01-2021, 11:22 AM
Last Post: OpalRose
  Questions about TiMax setting on AirCurve 10 SakimaStorm 15 278 07-31-2021, 03:10 PM
Last Post: SakimaStorm
  AirCurve 10 in ASV mode waitedwaytoolong 18 366 07-30-2021, 09:12 PM
Last Post: Sleeprider
  [Treatment] Need some help to start treating me apnea with S10 AirCurve VAuto SleepingForest 33 610 07-28-2021, 12:55 AM
Last Post: SleepingForest
  [CPAP] [mb635] - AirSense 10 Autoset to Aircurve 10 ASV mb635 112 4,727 07-27-2021, 05:49 PM
Last Post: mb635


New Posts   Today's Posts






About Apnea Board

Apnea Board is an educational web site designed to empower Sleep Apnea patients.